Printer Engine Service Mode
The Printer Engine Service mode is used to check electrical data, change modes, and adjust values.
Here is a quick summary of how to enter and use the Printer Engine Service mode to change the settings
listed in the Service Program Mode Tables.
1.
Press and
together, hold down for over 5 seconds, release and then press [#Enter].
2.
Press or
to display “2.Engine”.
3.
Press [#Enter].
4.
Press
or
to display the SP code groups.
1. Feed
SP1000
2. Drum
SP2000
3. Process
SP3000
5. Mode
SP5000
6. Periphs
SP6000
7. Data Log
SP7000
8. Data Log2
SP8000
9. Etc.
SP9000
1.
Press
or
to select the group, and then press [#Enter].
• The 2-line display is rotational. If you press
with “1.Feed” displayed, the display will jump
to "9. Etc.", the last selection. Similarly, if you press
with “9.Etc” displayed, the display will
jump to “1.Feed”, the first selection.
2.
While referring to the Service Program Mode Tables, press
or
to select the SP that you
want to change, and then press [#Enter].
• If you see > or >> to the right of a selection name, this means a menu sublevel exists.
3.
Follow one of the procedures below to change a setting.
To change a single-digit number setting:
• Press [#Enter]. A number replaces the cursor.
• Press
or
to increase or decrease the number.
• Press [#Enter]. The number selected on the 2nd line replaces the number above.
5. Service Tables
184
5
Содержание A-P4
