background image

-  - 

13

 

microwave over will consume 40% to 100% more than its 

advertised cooking power. Check the rating sticker on the 

back of the over to determine its actual power draw.   

 

The Power inverter may not be able to start some motors 

even though their rated current draw is within the power 

inverter. If motor refuse to start, observe the battery 

voltage indicator while trying to start the motor. If the 

battery voltage indicator drops below 11 volts while 

inverter is attempting to start the motor, this may be why 

the motor won’t start. Make sure that the battery 

connections are good and that the battery is fully charged. 

If the connections are good and the battery is charged, 

but the voltage still drops below 11 volts, you may need to 

use a larger battery.   

 

K. Trouble shooting: 

 

K-1. Common problems Television interference: 

Operation of the power inverter can interfere with 

television reception on some channels. If this situation 

occurs, the following steps may help to alleviate the 

problem. 

 

Make sure that the chassis ground lug on the back 

of the power inverter is solidly connected to the 

ground system of your vehicle, boat or home.   

 

Do not operate high power loads with the power 

inverter while watching television. 

 

Make sure that the antenna feeding your television 

provides an adequate (“Snow free”) signal and that 

you are using. Good quality cable between the 

antenna and the television. 

 

Move the television as far away from the power 

Содержание INVERTEK U SERIES DAI-1000U-12xx






















Отзывы: