GENERAL EXPLANATION
PARTS
Table Top
Adjustable Height
Rear Locking Casters
2
If any components are damaged or missing, contact your authorized dealer immediately.
1. Table Top
2. Column Assembly (Release Rod not shown)
3. Adjustment Lever
- 20 x 2 " Bolt & Nut (1 each)
4
1
/
4
1
/
8
5. Mounting Bracket
6. Domed Phillips Head Bolts & Lock Washers (2 each)
6
7. Base
7
8. Casters, Locking (2 each)
8
9. Casters, Non-Locking (2 each)
11. Bolt Plate
11
13. Black Screw (DO NOT REMOVE until assembled)
14. Chrome Screw A (DO NOT REMOVE)
10. Bolt Sleeves (2 each)
- 15 x 2" Hex Bolts (2 each)
3
/
8
15. Chrome Screw B (To replace Black Screw after assembled)
5
12
ASSEMBLY INSTRUCTIONS
1
3
DO NOT REMOVE Chrome Screw A (14) marked “Do Not Remove”.
Apply light upward pressure anywhere on the table top and stop when the desired height is reached.
1
To Raise Table Top
Pull the Adjustment Lever upward and push down on the table top at the Column end.
end. When the Adjustment Lever is released, the Table Top will lock into place.
To Lower Table Top
The Casters on the Column end can be locked by stepping down on the tabs. To unlock, pull up on the tabs.
To Lock and Unlock Casters
Figure 1
Figure 2
4.
12.
OPERATING INSTRUCTIONS
Do not put pressure on the opposite
Prior to assembly please read all instructions and save for future use. If you do not
understand any part of these instructions, contact a health care professional or authorized
dealer for assistance.
8. Turn the table upright placing the Casters on the floor. While pressing down on the Table
Top, remove the Black Screw in the Column Assembly (2) and replace it with Chrome Screw B
(15) included in the hardware package.
7. Insert the Locking Casters (8) into the Base near the Column Assembly (2) and insert the
Non-Locking Casters (9) intothe opposite end of the Base (7). Be sure to press the casters
in until they lock into place.
DO NOT remove the Black Screw from Column Assembly until Table is fully assembled.
This product utilizes a high tension, spring loaded mechanism and could raise
suddenly causing personal injury. DO NOT over tighten or use power tools to assemble.
1. Place the Table Top (1) on a level surface so the Mounting Bracket (5) faces up.
2. Check the Column Assembly (2) to ensure the Release Rod (not shown) is completely inside and not
protruding.
3. With the curved side toward table top, insert Adjustment Lever (3) into opening at top of Column
Assembly (2) making sure flat side of Adjustment Lever (3) rests on elease Rod. (Fig 1)
4. While holding Adjustment Lever, insert short end of Column Assembly (2) into Mounting Bracket (5) and
insert the two Domed Phillips Head Bolts and Lock Washers (6) but do not tighten. (Fig. 2)
5. Align holes of Adjustment Lever (3), Column Assembly (2) and Mounting Bracket (5) and secure with 1/4 -
20 x 2 1/8” Bolt and Nut (4). (Fig. 1) Then, tighten the two Domed Phillips Head Screws (6) at top of
Mounting Bracket (5).
6.Take Base (7) with caster holes facing away from Table Top and place end with mounting holes on Column
Assembly (2). Insert two large hex bolts (12) through Bolt Plate (11), through Bolt Sleeves (10), through
Column Assembly (2). Insert two large hex bolts (12) through Bolt Plate (11), through Bolt Sleeves (10),
through the Base (7) and into Column Assembly (2). Tighten with wrench. (Fig 2)
