Rheem Solar Premier Loline Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 60

background image

CONNECTIONS – ELECTRICAL

36

The power supply to the booster heating unit can be either a

continuous / time of use

or an

Extended Off-

Peak (overnight and day)

power supply and may be controlled by a

Timer Control Switch

. Discuss the power

supply requirements to the booster heating unit with the householder. The power supply to the solar controls
must be a continuous power supply.

Continuous Power Supply

A single active is required from the switchboard if the solar
storage tank is connected to a continuous power supply.

The  active  from  the  continuous  circuit  must  be  connected
to  the  active  terminal  marked  A1  (marked  “Controller”  on
the  wiring  diagram)  on  the  terminal  block  of  the  solar
storage tank.

A wire is supplied bridging the two active terminals marked
A1 and A2 (marked “Controller” and “Booster” respectively
on  the  wiring  diagram)  on  the  terminal  block  of  the  solar
storage  tank.  This  is  required  if  the  water  heater  is
connected  to  a  continuous  power  supply  and  a  timer
control switch is not installed in the power supply circuit to
the booster heating unit.

Refer  to  the

continuous power supply wiring connection

diagram

on page 36.

A timer control switch can be installed in the power supply
circuit to the booster heating unit. Refer to

“Booster

Control”

on page 37.

Extended Off-Peak Power Supply

Two  actives  from  two  separate  circuits  are  required  from
the switchboard if the booster heating unit is connected to
an  Extended  Off-Peak  power  supply.  A  double  pole
isolating  switch  is  required  to  be  installed  at  the
switchboard to simultaneously isolate both circuits.

The  active  from  the  continuous  circuit  must  be  connected
directly  to  the  active  terminal  marked  A1  (marked
“Controller” on the wiring diagram) on the terminal block of
the  solar  storage  tank.  This  supply  must  remain
uninterrupted  to  allow  the  solar  controls  to  operate  and
solar gain to be achieved.

The  active  wire  from  the  Extended  Off-Peak  Circuit  must
be  connected  to  the  active  terminal  marked  A2  (marked
“Booster”  on  the  wiring  diagram)  on  the  terminal  block  of
the solar storage tank.

The wire bridging the two  active terminals marked A1 and
A2 (marked “Controller” and “Booster” respectively on the
wiring  diagram)  on  the  terminal  block  is  not  required  and
must  be  removed  if  the  booster  heating  unit  is  connected
to an Extended Off-Peak power supply.

Refer to the

extended off-peak power supply wiring connection diagram

on page 36.

A timer control switch can be installed in the power supply circuit to the booster heating unit. Refer to

“Booster Control”

on page 37.

TIMER WITH CONTACTOR (if required)

WIRING CONNECTION DIAGRAMS - DRAINBACK ELECTRIC

SOLAR WATER HEATER

Timer

Continuous Power Supply

(no timer)

Continuous Power Supply

(no booster)

Extended Off-Peak Power Supply

(no timer)

Continuous Power Supply

Switchboard

Extended Off-Peak

Power Supply

Switchboard

TIMER WITHOUT CONTACTOR

Terminal Block

TIMER WITH CONTACTOR (if required)

WIRING CONNECTION DIAGRAMS - DRAINBACK ELECTRIC

SOLAR WATER HEATER

Timer

Continuous Power Supply

(no timer)

Continuous Power Supply

(no booster)

Extended Off-Peak Power Supply

(no timer)

Continuous Power Supply

Switchboard

Extended Off-Peak

Power Supply

Switchboard

TIMER WITHOUT CONTACTOR

Terminal Block

Continuous Power Supply Connection

to the Booster Heating Unit

TIMER WITH CONTACTOR (if required)

WIRING CONNECTION DIAGRAMS - DRAINBACK ELECTRIC

SOLAR WATER HEATER

Timer

Continuous Power Supply

(no timer)

Continuous Power Supply

(no booster)

Extended Off-Peak Power Supply

(no timer)

Continuous Power Supply

Switchboard

Extended Off-Peak

Power Supply

Switchboard

TIMER WITHOUT CONTACTOR

Terminal Block

TIMER WITH CONTACTOR (if required)

WIRING CONNECTION DIAGRAMS - DRAINBACK ELECTRIC

SOLAR WATER HEATER

Timer

Continuous Power Supply

(no timer)

Continuous Power Supply

(no booster)

Extended Off-Peak Power Supply

(no timer)

Continuous Power Supply

Switchboard

Extended Off-Peak

Power Supply

Switchboard

TIMER WITHOUT CONTACTOR

Terminal Block

Extended Off-Peak Power Supply Connection

to the Booster Heating Unit

«
...
34
35
36
37
38
...
»

Содержание Solar Premier Loline





























































Отзывы:

Нет отзывов

Похожие инструкции для Solar Premier Loline

Бренд: JBL Страницы: 12

Бренд: GEA Страницы: 337

Бренд: QualityCraft Страницы: 10

Бренд: BLACKMER Страницы: 12

Бренд: German pool Страницы: 17

Бренд: hajdu Страницы: 72

Бренд: Lasko Страницы: 4

FLOJET G55 Series

Бренд: Xylem Страницы: 2

Бренд: Rinnai Страницы: 34

Бренд: Reznor Страницы: 31

NO FRILLS 1000 GPD

Бренд: PureWater Страницы: 32

Infra Fix CLASSIC

Бренд: Barbecook Страницы: 122

Бренд: Eterna Страницы: 2

Бренд: Mathius Страницы: 6

Бренд: Ballu Страницы: 11

PowerFLO 7800 Series

Бренд: Delavan Страницы: 2

Бренд: kbice Страницы: 19

Бренд: Dimplex Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды