background image

TABLE OF CONTENTS 

 

INTRODUCTION .......................................................................................... 1 

SECTION 1  INSTALLATION ...................................................................... 2 

Site Location, Preparation & Unit Positioning ................................................................ 2 
Plumbing ....................................................................................................................... 3 
Chemical Treatment ...................................................................................................... 3 
Electrical ....................................................................................................................... 4 
Control Design for Pool Heating .................................................................................... 4 
Link between Heat Pump, Water Pump and Thermostat for Pool Heating ..................... 4 
Precautions ................................................................................................................... 5 

 
 

SECTION 2  COMMISSIONING ................................................................... 6 

SECTION 3  OPERATION ........................................................................... 6 

Thermostat Operation .................................................................................................. 7 
Heat Up Time ............................................................................................................... 7 
De-Icing ........................................................................................................................ 7 
Pool Application ........................................................................................................... 7 

 

SECTION 4  MAINTENANCE ...................................................................... 7 

Heat Exchanger Care .................................................................................................... 8 
Service Assistance ........................................................................................................ 8 

 
 

SECTION 5  TROUBLESHOOTING ............................................................. 9 

Machine Will Not Start .................................................................................................. 9 
Pool Will Not Heat ........................................................................................................ 9 
Compressor Will Not Run ............................................................................................. 9 
Compressor Motor Hums But Will Not Start.................................................................. 9 

 

SECTION 6  INSTALLATION SCHEMATIC DRAWINGS ............................ 10 

Typical Single Pool Heat Pump Schematic For Pool Filtration ...................................10 
Typical Single Pool Heating Schematic ......................................................................10 
Typical Multiple Pool Heat Pump Installation .............................................................11 

 

SECTION 7  WARRANTY .......................................................................... 12 

 

 

Содержание RTHP009

















Отзывы: