background image

SAVE A SERVICE CALL 

16 

 

Water heater size 

Do you have the correct size water heater for your requirements? The sizing 
guide  in  the  Rheem  sales  literature  and  on  the  Rheem  website 

(www.rheem.com.au)

 suggests average sizes that may be needed. 

 

WATER TEMPERATURE TOO HIGH 

A  RheemPlus  water  heater  is  fitted  with  a  temperature  limiting  valve  set  to 
deliver  water  not  exceeding  50°C.  If  the  water  is  being  delivered  at  a 
temperature exceeding 50°C, phone Rheem Service or their nearest Accredited 
Service  Agent  to  arrange  for  an  inspection.  Care  must  be  taken  by  all 
householders when using hot water until the valve is serviced or replaced. 
 

TEMPERATURE PRESSURE RELIEF VALVE RUNNING 

 

Normal Operation 

It  is  normal  and  desirable  that  this  valve 
allows  a  small  quantity  of  water  to  escape 
during  the  heating  cycle.  However,  if  it 
discharges more than a bucket full of water 
in 24 hours, there may be another problem. 

 

Continuous dribble 

Try  gently  raising  the  easing  lever  on  the 
relief  valve  for  a  few  seconds  (refer  to 

“Temperature  Pressure  Relief  Valve”

  on 

page 9).  This  may  dislodge  a  small  particle 
of  foreign  matter  and  clear  the  fault. 
Release the lever gently. 

 

Steady  flows  for  long  period  (often  at 
night) 

This may indicate the mains water pressure 
sometimes  rises  above  the  designed 
pressure  of  the  water  heater.  Ask  your 
installing  plumber  to  fit  a  pressure  limiting 
valve. 
 

  Warning:

  Never  replace  the  relief  valve  with  one  of  a  higher  pressure 

rating. 

 

Heavy  flows  of  hot  water  until  water  heater  is  cold  -  then  stops  until 
water reheats 

The  water  heater 

must

  be  switched  off  at  the  switchboard.  Phone  Rheem 

Service  or  their  nearest  Accredited  Service  Agent  to  arrange  for  an 
inspection. 

 

 

Содержание Gas Domestic Indoor Water Heater









































Отзывы: