Rheem Gas Domestic Indoor Water Heater страница 36 Скачать руководство пользователя | Manualshive

Страница: 36 / 40

background image

COMMISSIONING

36

Turn the adjusting knob on
the temperature limiting valve
counter-clockwise

(down

away from the water heater),
using a 6 mm Allen key.

Turning the adjusting knob
counter

clockwise

(down

away from the water heater)
increases the outlet water
temperature,

turning

it

clockwise (up towards the
water heater) decreases the
outlet water temperature.

Repeat the water temperature measurement from the same hot tap.

Further  adjust  the  temperature  limiting  valve  as  required,  turning  the
adjusting knob either counter clockwise (down away from the water heater)
or  clockwise  (up  towards  the  water  heater)  to  increase  or  decrease  the
outlet  water  temperature,  until  an  acceptable  water  temperature  not
exceeding 50°C is measured at the same hot tap.

Turn off the hot tap.

Replace the insulation and plastic casing to cover the temperature limiting
valve and pipe work on the side of the water heater and secure using the
three (3) retaining screws.

RHEEMPLUS TEMPERATURE ADJUSTMENT

«
...
34
35
36
37
38
...
»

Содержание Gas Domestic Indoor Water Heater









































Отзывы:

Нет отзывов

Похожие инструкции для Gas Domestic Indoor Water Heater

Бренд: Bartscher Страницы: 18

Бренд: Salamander Pumps Страницы: 24

Бренд: X-POWER Страницы: 44

Бренд: Napoleon Страницы: 20

Бренд: Napoleon Страницы: 40

Бренд: INOXPA Страницы: 20

POWERMASTER III

Бренд: Lincoln Страницы: 6

Delta Solo Compact MVP Series

Бренд: KSB Страницы: 40

Бренд: Davey Страницы: 4

Бренд: SMC Networks Страницы: 19

Бренд: Bionaire Страницы: 8

Бренд: VonHaus Страницы: 10

Бренд: Reefe Страницы: 12

Бренд: Davey Страницы: 20

Бренд: Vanguard Страницы: 20

Бренд: Powerhorse Страницы: 48

MAG HK 13-2/0-3 H

Бренд: Vaillant Страницы: 12

Бренд: GREADEN Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды