manualshive.com logo in svg

Rheem 627 series, Руководство пользователя и инструкции по установке, Страница: 38 / 56

Поделиться
Скачать
Rheem 627 series Скачать руководство пользователя страница 38

FLUEING 

38 

VERTICAL FLUE INSTALLATION 

Suitable flashing (not supplied) is required to waterproof the roof penetration. 
 

Notes: 

 

Ensure  each  flue  component  is  fully  engaged  and  the  rubber  seal  on  the  inner  duct  is  well  seated  at 
each joint. 

 

Each flue component is supplied with screws to connect to the adjacent flue component. The screws are 
located in a bag taped to the outside of the flue component. 

 

Refer to diagrams: 

 

“Typical Installation – Vertical Flue”

 on page 32, and 

 

“Typical Installation – Vertical Terminal with Vertical and Horizontal Sections”

 on page 32. 

 
To install a vertical flue and termination: 

1. 

Determine the location where the flue will penetrate through the roof. 

Note:

 Ensure there are no rafters, purlins, pipes or electrical cables located in the roof where the flue is 

to penetrate. 

2. 

Drill  or  cut  the  flue  termination  holes  through  the  roof  and  ceiling  of  a  suitable  size  to  allow  the 
installation of the flue, using a cutting tool suitable for the roof construction. 

3. 

Install  a  Condensate  Trap  (PN  295139)  to 
the  condensate  drain  spigot  on  the  water 
heater flue outlet. 

 

Install  a  condensate  drain  line  to  the 
Condensate Trap. 

Refer  to 

“Draining  the  Condensate”

  on 

page 29  and  to 

“Condensate  Trap  and 

Condensate Drain Line”

 on page 30. 

4. 

Connect the first flue component to the water 
heater flue outlet. 

 

Fit  the  end  of  the  flue  component down 
over  the  water  heater  flue  outlet  as  far 
as it will go. 

Ensure there is a minimum 35 mm and maximum 42 mm 
overlap,  the  rubber  seal  on  the  inner  flue  is  well  seated 
and  the  flue  component  is  fully  engaged  on  the  water 
heater flue outlet. 

 

Secure the bend to the outlet with the screws provided. 

5. 

Continuing  from  the  first  flue  component  and  working 
towards  the  terminal  location,  connect  all  of  the  other  flue 
system components. 

 

Ensure  each  flue  component  is  fully  engaged  and  the 
rubber seal on the inner duct is well seated at each joint. 

6. 

Horizontal  flue  runs  between  bends  must  have  a  minimum 
upward  gradient  towards  the  flue  terminal  of  20 mm  per 
metre. 

Note:

  Ensure  that  the  seam  of  the  inner  flue  in  horizontal 

runs is towards the top of the installation. 

7. 

Secure each flue component using the sheet metal screws provided. 

 

 
 

 

CONDENSATE
SPIGOT

CONDENSATE SPIGOT LOCATION

CFWH 627 INDOOR MODELS

SK7166-5 REV AD 1/12

REMOVE
CLIP

REMOVE
RUBBER CAP

 

 

condensate drain spigot 

Содержание 627 series

























































Отзывы:

Нет отзывов