VSP 3600 Quick Start
Version 1.1
Page 2 of 4
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197 Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
Step 9- Power Port
Plug in power cord which has IEC connector, VSP
3600 has two power ports with one for backup power
and support AC power from 90 to 264 VAC,50-60Hz,
which means world wide compatible.
Step 1-Set Output Resolution
Press MENU button, and spin Up/Down knob to select
OUTPUT CONFIG. Press NEXT and spin Up/Down
knob to select OUTPUT FORMAT. Press NEXT and
spin Left/Right knob to select OUTPUT
RESOLUTION. Then press NEXT to setup.
1024×768×60Hz, 1280×720×60Hz,1280×768×60Hz,
1280×1024×60Hz,1360x768x60Hz,1366x768x60Hz,
1400x1050x60Hz,1440x900x60Hz,1600×1200×60Hz,
1680x1050x60Hz,1920×1080×60Hz,1920x1200x60Hz,
2048x1152x60Hz
；
Step 2-Programming input signal
Power On
Push power button switcher to ON position. LCD
module on the front panel will show Video Processor
and VSP 3600 model information, and go into self
verification before it load the last setting configuration
data and send the processed image to the target display
or device. For the first time running, CV1 input is the
default input source.User can operate with VSP 3600
with local front panel and remote control with the
software run on the PC, remote control by RS232, USB
or TCP/IP.
RS-232
Function
2
TX
Transmit
3
RX
Receive
5
GND
Signal Ground
7
---
Not Used
8
---
Not Used
Pin
RS-422
Function
TX-
Transmit(-)
RX-
Receive(-)
GND
Signal Ground
RX+
R)
TX+
Tr)
Insert Twisted
Pair Wires
RS232/RS422
Connector
Insert Twisted
Pair Wires
RJ11 Connector
RJ-11
Function
1
TX
Transmit
2
RX
Receive
3
GND
Signal Ground
4
---
Not Used
Pin
Local Control-Front Panel Operation
VSP 3600 supports 4 DVI( compatible with HDM1.3),
and supports max input resolution 2048x1152x60Hz.
NOTE
Operating as following
：
1. In LAYER part, it can be programmed only when
A, B, C, D button lights and blinks;
2. In FUNCTIONS part, push Program button to light;
3. In SOURCES part, push button to select 1, 2, 3, 4, it
will light to show that its corresponding channel is
programmed into the current layer;
4. In FUNCTIONS part, push Program and its light
will be out to show the program operation of channels
is completed.
Step 3-Set Output
1. In OUTPUTS part, push DVI1, DVI2, DVI3, DVI4
and it will light to show it is being programmed;
OUTPUTS part button DVI1 is correspond with DVI1
and VGA1;
OUTPUTS part button DVI2 is correspond with DVI2
and VGA2;
OUTPUTS part button DVI3 is correspond with DVI3
and VGA3;
OUTPUTS part button DVI4 is correspond with DVI4
and VGA4;
2. In FUNCTIONS part, push Add Layer to add layer
to output channel which means adding the quantity of
layer;
3. In FUNCTIONS part, push Clear Layer to reduce
layer of output channel which means reducing the
quantity of layer;
4. In LAYER FUNCTIONS part, push Program to
program input channel which means program the input
signal of output screen;
5. In CUSTOM ADJUSTMENTS part, push Scale to
adjust the size of image which means to scale or zoom
of the image;
6. In CUSTOM ADJUSTMENTS part, push Crop to
crop the image which means to crop the input signal of
the output screen;
7. In CUSTOM ADJUSTMENTS part, push Position
to adjust the position of the corresponding input image
of the layer which means to adjust the position of
output screen.
Step 8- Serial Port
Use RS232 to RJ11 cable to connect a control system
or computer to the back panel RJ11 port and the other
end on RS232 port. RS232 to RJ11 cable as following
definition.
VSP 3600 supports output resolution as
following
：
NOTE
