background image

23/25 

 

   

HEALTH & SAFETY STATEMENT

 

 

13.1 General 

 

Under the Consumer Protection Act 1987 and 
Section 6 of the Health and Safety at Work Act 1974 
we hereby provide the following information on 
substances hazardous to health. 
Product range reference LCSA-4 air heaters. 

 
 

13.2 Cautionary note

 

 

During first firing some smoking may occur, this is 
due to the burning off of protective/lubricating oils 
used during appliance production. Most of this will 
have been removed during the production testing 
process. It is a wise precaution to ensure that 
adequate ventilation is provided during the initial 
firing and throughout the commissioning period, this 
is particularly important if the discharge air is to blow 
into a confined space. This smoking does not 
constitute a poison hazard. 

 
 

13.3 Declaration 

 

LCSA heaters contain no asbestos;  copper is not 
employed in gas carrying components;  solder which 
has a melting point below 450°C is not used;  paints 
for corrosion protection and decoration are heat 
cured and contain no lead. 
The above appliances meet the Electrical Safety 
requirements of EN60 335 Pt 1 1988. 

 
 

13.4 Miscellaneous 

 

Small quantities of adhesives and sealants used in 
the product are dried and cured and present no 
known hazard. 

 
 

13.5  Insulation and Seals

 

Material:  Alumino - silicon fiber - crane glass 
Description:  Tapes 
Known hazards: Some people can suffer reddening 
and itching of the skin.  Fiber entry into the eyes will 
cause foreign body irritation. Inhalation will cause 
irritation to the respiratory tract. 
Precautions: Wear protective gloves when handling. 
People with a history of skin complaints may be 
susceptible to irritation. 
Dust levels are only likely when the material is 
abraded. 
In general normal handling and use for this purpose 
will not present discomfort.  Follow good hygiene 
practices, wash hands before

 

consuming food or 

using the toilet. 
First Aid: Medical attention must be sought following 
eye contact or prolonged reddening of the skin. 
 

 

 

13.6 Thermostat

 

Material: Illuminating Kerosene. 
Description: Sealed phial contains a small quantity in 
liquid form. 
Recognition: Colorless liquid, paraffin oil/petroleum 
hydrocarbon odor. 
Characteristics: Non-corrosive, flammable with no 
poisonous reference-CH poison Class 3 
Precautions: Avoid handling. This product can irritate 
and defat the skin. Prolonged contact may cause 
dermatitis. Avoid breathing vapor. Avoid eye contact. 
Do not ingest. 
First Aid: Skin. Wash thoroughly with soap and water. 
Eyes. Rinse immediately with copious amounts of 
clean water. 
Ingestion: Seek medical advice. 
 
NOTE: If skin irritation persists seek medical advice. 
 

 

13.7 Electrolytic  Capacitor 

 

Two types are used by random selection: 
Recognition: 1. Plastic enclosure 2. Aluminium 
enclosure 
Material: Contained liquid electrolyte 
Known hazards: Electric shock possible if charged. 
Precautions: Discharge to ground/earth. Do not 
incinerate. 
First Aid: Treat for electric shock if affected. 

13 

Содержание 100


























Отзывы: