Reynolds Building Systems Best Barns USA Glenwood Скачать руководство пользователя | Manualshive

Страница: 15 / 20

background image

5.

Install (2) two 6' long soffit panels.

Soffit

Step 17

Install Sidewall Trim & Soffit

96-3/4' Long Corner Trim

1.

Install a 96-3/4" long 1x4 trim board flush with the

corner trim on the back of the building.

This trim board

has blue paint on one end

. Locate a 7/16" x 3" x 8"

gauge block packed in the hardware bag. Place
this gauge block under the truss overhang and
butt the corner trim against it.

It will be easier to install the soffit panel if the corner and sidewall trim are installed first.
This enables the soffit panels to rest on the trim where it meets the building. See lower detail.

3.

Install 1x4-12' trim along the top of the side-

wall and cut another 4' long board to finish.

7/16" Gauge Block

1x4 Trim

Bevel Edge

4.

Install 10-5/8" soffit panels under the truss

overhangs. Use 5d galv. nails. Install the soffit
with the beveled edge toward the ends of the
trusses. Cut a 4' long panel to the center of
the truss.

2.

Install 4' long 1x4 trim along the top

of the sidewall. Use the gauge block
to set where the trim will be installed.

«
...
13
14
15
16
17
...
»

Содержание Best Barns USA Glenwood





















Отзывы:

Нет отзывов

Похожие инструкции для Best Barns USA Glenwood

Бренд: Tarptent Страницы: 2

Sportz Cove 61500

Бренд: Napier Страницы: 7

Бренд: Snow Peak Страницы: 16

Бренд: Hilleberg Страницы: 8

TRENTON 2105126

Бренд: Backyard Discovery Страницы: 35

Бренд: ABSCO SHEDS Страницы: 29

Бренд: ABSCO SHEDS Страницы: 28

Бренд: Strongway Страницы: 12

Бренд: Campvalley Страницы: 2

Бренд: NRSRelief Страницы: 11

Бренд: Dometic Страницы: 16

Бренд: Axley Страницы: 8

Бренд: Dancover Страницы: 6

Бренд: Garden Treasures Страницы: 4

Бренд: Zolia Страницы: 3

Бренд: canvascamp Страницы: 2

Бренд: Texsport Страницы: 1

01831 Calypso Cabana

Бренд: Texsport Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды