Reynolds Building Systems Best Barns USA Glenwood Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 20

Reynolds Building Systems Best Barns USA Glenwood Скачать руководство пользователя страница 12

flush

3.

Install 95" long 1x4 white pine trim

boards as corner trim to the rear
walls. Install trim flush with the
siding on the sidewalls.

4.

Repeat to install trim boards to the

front wall panel.

Back

Wall

Side

Wall

Filler

1x4 Corner Trim

Step 12

Install Corner Trim

Tie Plate

Step 11 Install 2x4 Tie Plates

1.

Cut a 2x4-8' board to 4' and install on the side wall, at the back corner of the building as shown

below. Use 10d sinkers. Install a 2x4-8' in the center of the sidewall. Install another 4' long
2x4 at the front corner. Repeat to install 2x4s on the opposite side walls.

3.

Cut a 6' long 2x4 in half and install 3' long 2x4s at the rear corners. Cut and install a 6' long

2x4 between the 3' long 2x4s.

2x4-4' Tie Plate

Cut 2x4-6' to Fit

IMPORTANT: Lower Trim Must Be Installed Before Installing Roof Gables!

1.

Tack 1-1/2" x 48" filler strips on top of the siding on the back wall.

2.

Install (2) two 72-3/8" long 1x4 white pine trim boards flush with the siding on the sidewalls

and flush with the top of the 2x4 tie plate. Use 8d galv. nails to install all trim.

2x4-8' Tie Plate

Flush

1x4 Trim Boards

2x4-8' Tie Plate

«
...
10
11
12
13
14
...
»

Содержание Best Barns USA Glenwood





















Отзывы:

Нет отзывов