background image

g)   Remain seated quietly for at least 5 minutes before you begin the 

measurement.

h)  For those who cannot put the cuff on the left arm, put it on the right arm as 

shown.

i)  Consecutive measurements will cause blood accumulation in the lower arm 

which will affect the measuring results. To improve reading accuracy, raise 

the arm being measured, squeeze and relax your hand several times, then 

take another measurement. Another option is to take the cuff off and wait at 

least 5 minutes before repeating measurement.

j)  If this device was stored in low temperature, it is necessary to leave it in 

room temperature for at least 1 hour, otherwise the measurement can be inaccurate.

Comment:

Continue to use the same arm for comparisons.  It is not unusual for there to be a difference in blood pressure 

between arms.

Comparable blood pressure measurements always require the same conditions (relax for several minutes before 

taking a measurement).

3.4 Measuring Your Blood Pressure

After the cuff has been appropriately positioned, the measurement can begin:

1.  Press the 

START/STOP

 button until all the symbols appear on the screen, after “ ” will 

flash for 2 seconds. The pump then begins to inflate the cuff. The increasing pressure in 

the cuff is shown on the display.

2.  After the suitable pressure has been reached, the pump stops and the cuff gradually 

deflates. The cuff pressure will then be displayed. In case the initial inflation is not 

sufficient, the device automatically re-inflates to a higher pressure.

3.  When the device detects a heartbeat, the heart symbol “ ” on the display starts to flash 

for every heartbeat.

4.  When the measurement has been completed, the systolic, diastolic and pulse rate will 

appear on the display.

5.  The measurement readings remain on the display until you switch off the device. If no 

button is pressed, the device switches off itself in 3 minutes.

NOTE:

 The symbol “ ” will be displayed along with the reading if irregular heartbeat has 

been detected during the measurement. If the “ ” symbol appears frequently (e.g. several 

times a week), it may be an indication of a more serious heart problem, and you should consult your doctor.

Cuff on

right arm

M

D

PM

M

D

PM

M

D

PM

Содержание RX810


















Отзывы: