REVV Generator 120 Скачать руководство пользователя страница 8

Страница: 8 / 43

Revv Owner’s Manual - 8

Channel Two (Crunch)

Selected by:

pushing the designated front panel momentary toggle

switch down,

footswitch button #2 or a footswitch preset mode set-

ting,

MIDI & CC commands.

Passive

treble, middle,

bass

controls with a wide range. Small turns =

large tonal change!

Crunch Bright

allows you to tailor the sound to your preferences by

shifting the high end response of this channel. It makes quite a large

difference, so don’t be afraid to turn it on if you like a much more bitey

tone! Pairing this on/off position with dialing of the treble knob can yield

very powerful results.

Crunch Gain

allows you to go from an almost totally clean tone to quite a

bit of gain! Most people do not use this past noon or so - but if you go

above 3 O’Clock you will experience some cool fuzz-like tones you may

find useful!

The

Output Power Switch

operates separately of all other channels & is

useful to decrease power to 10 watts for a saggier sound & feel or

simply a large volume decrease.

2.3

Содержание Generator 120












































Результаты поиска

Содержание Generator 120

Отзывы:

Бренды по названию

Популярные бренды

REVV Generator 120, Руководство пользователя

Результаты поиска

Содержание Generator 120

Отзывы:

Бренды по названию

Популярные бренды