REVV Generator 120 Скачать руководство пользователя страница 41

Страница: 41 / 43

Revv Owner’s Manual - 41

Amp Memory Reset (Factory Default)

If you would like to clear the amp’s memory of all saved program patches

& restore all of the amps settings to the factory default, which includes

MIDI channel (restored to CH1), OMNI Mode, FX Loop (Restored to off at

power up) & a full memory clear, proceed with the procedure below:

With power OFF, press & hold CH3 toggle switch (up) & the CH4 aggres-

sion switch (down) together & turn the power switch to the ON position.

The amplifier will flash the CH3 & CH4 LEDs to confirm that the factory

defaults have been restored.

Specifications

—

4 Channels: Clean, Crunch, Purple Gain, & Red Gain

—

Independent output power control on each channel

—

Intelligent foot control capabilities

—

MIDI capabilities

—

CC control of all functions

—

OMNI functionality

—

3 band EQ per c voicing switches

—

REVV tube arrangement: 5 - 12AX7, 1 - 12AT7, 4 - 6L6GC

—

Presence & depth control

—

Two master volume controls

—

4, 8, 16 ohm output impedance speaker jacks

—

Baltic birch head shell

—

Dimensions: 26.5” × 10” × 10.5”

—

Weight: 45 lbs

8.0

9.0

Содержание Generator 120












































Результаты поиска

Содержание Generator 120

Отзывы:

Бренды по названию

Популярные бренды

REVV Generator 120, Руководство пользователя

Результаты поиска

Содержание Generator 120

Отзывы:

Бренды по названию

Популярные бренды