manualshive.com logo in svg

REVV Generator 100, Руководство пользователя

Поделиться
Скачать
REVV Generator 100 Скачать руководство пользователя страница 32

Revv Owner’s Manual - 32

Note: There are only 3 channel LEDS & one aggression LED, so the MIDI 

channel count will be done in values of 4. MIDI channel 1 will be signified 

by CH1 CLEAN   LED flashing, & as you increase in number, MIDI channel 

4 will be signified by all three channel LEDS & the aggression LED flash-

ing, but once MIDI channel 5 is selected, only the CH1 CLEAN LED will 

flash again. Every time you reach MIDI channel 5, 9, or 13, the LED cycle 

will once again start from the CH1 CLEAN LED. So keep count as you 

select the channel you desire. If you go past MIDI channel 16, the count 

will start at channel 1 again. Once saved to memory, the Channel LEDs 

will flash very quickly a number of times to verify the change has been 

made & completed. The amp will then restart, completing the MIDI chan-

nel change procedure. 

MIDI Program Change

This amplifier can remember up to 128 program settings of the MIDI con-

trollable functions. In order to set a program (i.e. amplifier configuration) to 

be controlled via MIDI: 

1)

 Set the amplifier to the configuration you intend to save to a program 

number. (Ex: Ch: 2, Aggression level: 2, Fat: ON, Master Volume: 2, FX 

Loop: OFF, etc) 

2)

 Once the amplifier is configured as you would like, press the store 

switch. The Store LED will flash & the amplifier will wait now for a com-

mand through its MIDI IN jack. 

3)

 Send a program change command from your MIDI Pedal or other 

equipment with the correct channel & program number you intend to 

have the amplifier save the current configuration to. 

4)

 Once the command is received, the amplifier will save the current amp 

configuration to that program number. The Store LED will flash 3 times & 

turn off verifying that the command has been received & saved. 

6.3

Содержание Generator 100











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды