Revo Elite RESPTZ37-1 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 65

background image

NO

: Alarm input number

PRI(Priority)

: The lower number has higher priority. (0-8)

FUN(function)

: Stored function number to be called by alarm.

IN

: NO/NC - normally open /Closed OFF - ignore

OUT

: OUT1~OUT4 - Relay out 1,2,3,4, OFF - No output.

HLD(HOLD)

: Alarm will be held for programmed time (03 to 99 seconds)

LATCH

: ON - Shows all alarms including past alarm.

OFF - Shows activated alarms only.

DWELL

:means the dwell time during multiple alarms, 03 to 99 seconds.

The RELAY OUT setup is helpful when the outdoor housing is used with the dome.
Ex.) When you connect the relay output of the dome to the heater connector of the outdoor
housing, the relay output can operate during the setting time only.

RELAY OUT SETUP

OUT1 : ALARM

OUT2 : 1 MIN

OUT3 : ALARM

OUT4 : 5 MIN

EXIT(ESC TO EXIT)

ALARM:

the relay output is operated during an alarm operation or by the short key of our keyboard.

1-5 MIN(minute):

the relay output is operated during this setting time only by the function run of

the dome menu or the short key of our keyboard.

NOTE:

This

1-5 MIN

setting is not operated by an alarm.

NOTE: If you disable Alarm by dip switch, Alarm menu will be displayed following screen

.

ALARM SETUP

ALARM DISABLED

CHECK THE DIP SWITCH

EXIT(ESC TO EXIT)

There are 9 levels of priority. The function can be selected by Preset, Auto scan, Pattern or
Tour and “0” is the highest priority. Lower priority alarms won’t be serviced until the higher
priority alarm is completed. Equal priority alarms will be serviced repeatedly with the dwell
time.

20

«
...
24
25
26
27
28
...
»

Содержание Elite RESPTZ37-1


































































Отзывы:

Нет отзывов

Похожие инструкции для Elite RESPTZ37-1

Бренд: D-Link Страницы: 24

DCS-3110 - SECURICAM Fixed Network Camera

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 18

Бренд: Harbor Freight Tools Страницы: 3

Бренд: jablotron Страницы: 2

Бренд: Falcon Страницы: 4

Бренд: FALEEMI Страницы: 12

Бренд: Falconeyes Страницы: 2

Бренд: U-Prox Страницы: 29

Бренд: QOLSYS Страницы: 3

Бренд: ADEMCO Страницы: 56

Бренд: Digisol Страницы: 25

Бренд: FAAST Страницы: 12

Бренд: Comelit Страницы: 77

Бренд: NAVAC Страницы: 4

Бренд: TWUFY Страницы: 2

Бренд: Q-See Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды