REVENTON HC 20-EC Series, Техническая документация инструкция

Страница: 7 / 13

- air stators of the device have to be open in at least 30% before first start:
ź
standard version - opening of air stators must be done by two hands in parallel
ź
version with diffuser 360° - air stators of diffuser 360° must be done by two
hands to the outside
ź
version with confusor - the outlet do not have air stators which must be open
- using diffuser 360° or confusor causes decrease of device airflow of around
10% and consequently reduction of its heating capacity of about 5%
6. CONTROLS
Usage of automatic control dedicated to the air water heaters of Reventon
Group gives great possibilities of adjusting the efficiency of the heater
in different, depending on needs,
degree of its operation automation.
We can offer the following:
umo ż liwia sterowanie silnikami EC za pomoc ą sygna ł u steruj ą cego 0-10 V. S ł u ż y
do tego wygodny suwak, pozwalaj ą cy praktycznie regulowa ć wydajno ść
wentylatora w zakresie 0-100%. Potencjometr posiada równie ż dodatkowy styk
za łą czaj ą cy, odcinaj ą cy napi ę cie od wentylatorów, gdy nie ma potrzeby ich
pracy.
Output signal: 0 - 10 V
Power supply: 10 - 12 V DC / 1mA
Impedance: 10 k Ω + - 20%
Maximum load of the switching contact:
3 A / 230 V AC or 3 A / 12 V DC
Weight: 0.35 kg
Degree of protection: IP 54
is used to regulate equipped with EC motors. It is an advanced controller
with many functions i. a. operation in heating, cooling or mixed mode,
programmable mode, valve control, automatic selection of the fan speed.
Together with the controller an external sensor is provided, which allows to read
the temperature in the required place, even remote from the controller.
In addition, the device can be integrated with the BMS building control system
(using the MODBUS communication protocol).
Voltage/ Frequency: 230 V AC / 50 – 60 Hz
Maximum current: 5 A
Operating temperature range: 0 - 45°C
Regulation range: 5°C - 35°C
Regulation accuracy: ± 0.5°C
External temperature sensor: NTC 10K
Communication: RS485
Dimensions: 86 x 86 x 13.3 mm
Weight: 270 g
Degree of protection (housing): IP 20
Degree of protection (external sensor): IP 68
Potentiometer EC
Programmable controller HMI EC
Two-way valve with actuator ¾”
is used to automatically regulate the flow of the heating medium.
Voltage / Frequency: 230 V AC / 50 – 60 Hz
Power consumption: 2 VA
Kvs coefficient: 6.3 m³/h
Stroke: 3 mm
Operating condition of actuator: -5ºC - 60ºC
Running time: 3 - 5 min
Degree of protection: IP 54
is used to automatically regulate the flow of the heating medium.
Power supply/ Frequency: 230 V AC/ 50 – 60 Hz
Power consumption: 7 VA
Kvs coefficient: 6 . 5 m³/h
Operating condition of actuator: 0 - 60ºC
Running time (motor): 18 s
Running time (return spring): 5 s
Degree of protection: IP 20
Three-way valve with actuator HC 3/4"
Relay Module RM-16A
allows to connect a receiver with higher current consumption than permissible
current load of connected regulator.
Power supply/ Frequency : 230 V AC / 50 – 60 Hz
Maximum rated current: 16 A
Input : NO/COM
Input : SL Connection of a regulator
with the voltage relay 230 V
Dimension : 47 x 47 x 20 mm
controls operation of the heater. Switches the unit off automatically
when the set temperature is reached.
Power supply/ Frequency : 230 V AC / 50 – 60 Hz
Maximum rated current : 3 A
Operating temperature: 0 - 40°C
Temperature control range: 10 - 30°C
Control accuracy: <1°C
Degree of casing's protection: IP 30
Manual thermostat HC
Model HC 3 A HC 5 A HC 7 A
3
3
3
3
1
1
2
5
5
5
5
2
2
4
8
8
8
8
3
3
6
HC20-3S
HC30-3S
HC35-3S
HC45-3S
HC50-3S
HC70-3S
HMI HC3S
3
3
3
3
1
1
2
5
5
5
5
2
2
4
HC 14 A RM- 16 A
16
16
16
16
7
6
12
19
19
19
19
8
7
14
HC80-3S
HC 1.2 A
1
1
1
1
-
1
-
COOPERATION OF CONTROLLERS WITH EQUIPEMENT