manualshive.com logo in svg

REV Robotics SPARK, Руководство пользователя

Поделиться
Скачать
REV Robotics SPARK Скачать руководство пользователя страница 8

REV-11-1200-UM-00 

Copyright © 2016 REV Robotics, LLC 

8 

2.1.2

 

MOTOR OUTPUT 

Motor output terminals are located above the SPARK logo and are marked with raised lettering. A raised "+" and "−" sign 
indicate the polarity of the motor terminals. See Figure 2-1 for more details. 

 It is recommended to follow a polarity convention when connecting motors to multiple SPARKs so that each motor 
responds in a predictable manner to the same input signals. When the SPARK is driving the output in the "forward" 
direction, the output polarity is positive from M+ to M−. When driving in "reverse" the output polarity is reversed. 

2.1.3

 

POWER INPUT 

Power input terminals are located below the SPARK logo and are marked with raised lettering. A raised "+" and "−" sign 
indicate the polarity of the power terminals. 

The SPARK is intended to operate in a 12V DC robot system, however, it is compatible any DC power source between 
5.5V and 24V.  

 

When using high current motors, it is recommended to use a power source that is capable of handling large surge 
currents, e.g. a 12V lead-acid battery. If the supply voltage drops below 5.5V the SPARK will brown out, resulting in a 
power loss to the motor. It is also recommended to incorporate a fuse or auto-resetting circuit breaker in series with the 
SPARK between it and the power source to prevent exceeding the maximum current rating. 

 

2.1.4

 

CONNECTING MOTOR AND POWER WIRES 

Using an appropriate wire gauge for the expected current draw, tightly crimp either a ring or fork terminal on the wire. 
Insert the crimped terminal into the screw terminal and tighten the screw. Give the wire a tug to make sure it is secure. 
Figure 2-1 shows both motor and power wires connected to the SPARK. 

CAUTION 

DO NOT swap the motor and power connections. This can result in uncontrolled motor operation, can permanently 
damage the SPARK, and will void the warranty.

 

 

 

 

 

CAUTION 

DO NOT exceed the maximum supply voltage of 30V. Doing so will cause permanent damage to the SPARK and will void 
the warranty.

 

CAUTION 

DO NOT exceed the maximum current ratings of 60A or 100A for 2 seconds. Doing so will cause permanent damage to 
the SPARK and will void the warranty.

 

CAUTION 

As with any electrical component, make all connections with power turned off. Connecting the SPARK to a powered 
system may result in unexpected behavior and may pose a safety risk.

 

Содержание SPARK




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды