manualshive.com logo in svg

REV Robotics SPARK, Руководство пользователя

Поделиться
Скачать
REV Robotics SPARK Скачать руководство пользователя страница 11

REV-11-1200-UM-00 

Copyright © 2016 REV Robotics, LLC 

11 

2.4

 

LIMIT SWITCH INPUTS 

The SPARK has two limit switch inputs that, when triggered, can independently prevent motion in both the forward and 
reverse directions. 

2.4.1

 

LIMIT SWITCH OPERATION 

When the signal (s) pin is shorted to the ground (-) pin, the SPARK will override an input command for the corresponding 
direction and force the SPARK to its neutral state. The STATUS LED will turn white and pulse the corresponding 
direction color when either of the two limits are triggered and overriding the input command. See section 2.6 STATUS 
LED for more information. 

For example, if the Forward Limit Switch is triggered, a forward command from the PWM input is overridden and the 
output is forced into its neutral state. However, reverse commands are still accepted and sent to the output. 

2.4.2

 

LIMIT SWITCH WIRING 

The SPARK has two 3-pin connectors that can accept standard 3-wire sensor cables. The center pin is not used for the 
limit switch inputs. Figure 2-4 shows the locations of the Forward and Reverse ports and an example connection 
diagram. It is recommended to use a limit switch that is Normally Open (NO). When it is pressed, the switch closes and 
shorts the signal (s) and ground (-) pins. 

 

Figure 2-4 Limit Switch Inputs 

Содержание SPARK




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды