background image

necessary to space the Magnet/Detector off the

metal surface using a plastic or wooden spacer to

achieve the necessary radio range.

8. Remove the battery holder, then using the double

sided tape OR  the screws provided, mount the

Magnet to the door and the Detector to the door

frame (or vice-versa, if necessary).  Ensure that the

arrows on the Magnet and Detector are pointing

towards each other and that the gap between the

Detector and Magnet is less than 5 mm.  When

using the screws for mounting the Detector, ensure

that the small countersunk screw is used within the

battery compartment and that the screw is driven

flush with the inside of the casing.

9. Refit the battery holder (the Control Unit will emit a

3 second Tamper Alarm).

10. Refit the battery cover by placing it over the

batteries and sliding it on.

11. Test the operation by opening the door/window.

The LED on the Detector will light for approximately

1 second and then extinguish each time the

Magnet is moved away from the Detector, and the

Control Unit will emit a 3 second alarm tone each

time the Detector is operated.

When you have completed installing all your

Detectors, take the Control Unit out of Test mode

by entering

at the Control Unit.

EXTERNAL SOLAR SIREN

The Solar Siren Unit should be fitted to the outside of

the building in a position that is clearly visible and  at a

height which is relatively inaccessible to an intruder.

The Solar Siren incorporates a solar panel which will

maintain a charge to the integral 6 Volt 1.2Ahr sealed

lead acid rechargeable battery during daylight hours.

During the night, a negligible amount of energy is

released by the rechargeable battery to operate the

Siren.  The Solar Siren is self maintainable during

darkness and long winter periods.

LOCATION

To  provide the optimum amount on daylight to the 

Solar Panel, you should ideally mount the Solar Siren 

on a south facing wall.  However, an easterly or

westerly position will suffice.

Although the Solar Siren is designed to work on any

aspect wall, for optimum performance you should

refrain from siting the Unit on a north facing wall

where possible.  Shadows cast by neighbouring

walls, trees and roof overhangs should also be

avoided.  Where applicable, the Solar Siren should be

positioned a minimum of twice the width of the eaves

overhang below the eaves.  Remember that in winter

the sun is lower in the sky and you should avoid

winter shadows where possible.

The Solar Siren contains a sophisticated radio receiver.

However, reception of radio signals can be affected by

the presence of metallic objects within the vicinity of 

Access Code

?

?

?

?

Protector P500S

11

NORTH

WEST

EAST

SOUTH

Avoid if
possible

Содержание Protector P500S
























Отзывы: