REPLIGEN Spectrum KMPi Скачать руководство пользователя страница 55

Страница: 55 / 77

55 400-12355-000 Rev. 03

KR2

/ KMP

TFF Systems

Pump Head Setup and Operation

CAUTION: Be sure that bayonet features on back of each pump head are fully engaged with

bayonet tabs on the mounting plate or adjacent pump head before operating

pump drive. Bayonet lock lever (see Figure 5.) will snap back when bayonet

features engage completely.

KR2

Maintenance

No lubrication is required for the KrosFlo® Research II Pump Head. Only use a mild detergent

solution or 70% isopropyl alcohol to clean the pump head. Do not immerse nor use excessive fluid.

Pump head requires no maintenance beyond cleaning. There are no user serviceable or replaceable

parts inside.

9.4

KMP

Pump Head Operation

A flat-bladed screwdriver is required to complete installation.

Check that tang boot has plastic dampening to prevent damage to the pump shaft

Raise occlusion bed to expose mounting holes for top two short screws of Easy-Load Pump

Head

Aim back of Pump Head towards mounting plate to align pump shaft tang and five screw

holes (for Easy-Load Pump Head) or four screw holes (for High-Performance Pump Head)

NOTE:

Inspect the tang boot after 1,000 hours of operation and replace if necessary.

Insert mounting bolts into the mounting holes through the pump head and into the KMP

’s

mounting plate. On High-Performance Pump Head, use round mounting holes for left side

tubing entry and exit, or hexagonal mounting holes for top tubing entry and exit

Secure Pump Head to mounting plate and KMP

by tightening mounting bolt screws with

flat-bladed screwdriver

Figure 10: Drive with both pump

heads locked in position first

pump head

Содержание Spectrum KMPi














































































Результаты поиска

Содержание Spectrum KMPi

Отзывы:

Похожие инструкции для Spectrum KMPi

Бренды по названию

Популярные бренды

REPLIGEN Spectrum KMPi, Руководство пользователя и инструкции по эксплуатации

Результаты поиска

Содержание Spectrum KMPi

Отзывы:

Похожие инструкции для Spectrum KMPi

Бренды по названию

Популярные бренды