Reo-Pure LP3 Series Скачать руководство пользователя страница 21

Страница: 21 / 24

LP3-500 Owner’s Manual | 20

REO-PURE LP3-500 SYSTEM TROUBLESHOOTING

(continued)

PROBLEM

POSSIBLE CAUSE

SOLUTION

BAD

TASTING

WATER

Increase in feed water TDS

Check feed water TDS

Filter cartridges exhausted

Replace filter cartridges

Tank and system contaminated

Replace filter cartridges and membrane, sanitize

system and tank

Tank contaminated

Re-sanitize tank

Tank diaphragm ruptured

Replace tank

Membrane not flushed completely

Flush one or two tanks of product water to drain

CLOUDY

WATER

Dissolved air in feed water concentrated in

product water

Usually clears up as condition of feed water changes.

Letting water stand will allow dissolved air to dissipate

HIGH TDS IN

PRODUCT

WATER

Membrane element expended

Check, replace if necessary

Insufficient brine flow rate

Check, reject flow must be at least equal to product

flow

Increase in feed water TDS

Check inlet TDS, see Operating Specifications for

rejection rate.

Product tube o-rings damaged or out of place

Remove membrane element from housing. Re-install

or replace o-rings on membrane element product tube

Содержание LP3 Series

























Результаты поиска

Содержание LP3 Series

Отзывы:

Похожие инструкции для LP3 Series

Бренды по названию

Популярные бренды

Reo-Pure LP3 Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание LP3 Series

Отзывы:

Похожие инструкции для LP3 Series

Бренды по названию

Популярные бренды