manualshive.com logo in svg

Renishaw VIONiC RTLC20-S, Руководство по установке, Страница: 5 / 15

Поделиться
Скачать
Renishaw VIONiC RTLC20-S Скачать руководство пользователя страница 5

VIONiC RTLC20-S installation guide

3

Dimensions and tolerances in mm

VIONiC readhead installation drawing

*

Extent of mounting face.   

†

 Dimension from substrate surface.

Forward direction of 

readhead relative to scale

R > 30 Dynamic bend radius 
R > 10 Static bend radius

Ø4.25 

±0.2

5

Set-up LED

Optical centreline marker

A

0.6

35

23

11.5

6 

min

18

7.8

7.8

Reference mark selector 

sensor position

P and Q limit switch 
sensor position

Selected 

IN-TRAC 

™

 

reference mark

0.08

(Roll tol. ±0.5°)

13.5

4.25

4.15

10

8.75 

*

Offset 2.75 ±0.5

0.25

29

Detail A

Scale reading surface

5 

†

Mounting faces

Scale thickness 0.4 
(including adhesive)

P limit magnet 

Reference mark 
selector magnet 

Q limit magnet

Optical centreline 

(incremental and reference mark)

(Yaw tol. ±0.4°)

Rideheight: 2.1 ±0.15

(Pitch tol. ±1°)

2 mounting holes M2.5 through, 

counterbored Ø3 × 2.3 deep both sides.

NOTE:

 The recommended thread 

engagement is 5 min (7.5 including 
counterbore) and the recommended 
tightening torque is between  

0.25 and 0.4 Nm.

Содержание VIONiC RTLC20-S
















Отзывы:

Нет отзывов