manualshive.com logo in svg

Renishaw Vionic RTLC20/FASTRACK, Руководство по установке, Страница: 5 / 16

Поделиться
Скачать
Renishaw Vionic RTLC20/FASTRACK Скачать руководство пользователя страница 5

VIONiC RTLC20/

FASTRACK

 installation guide

3

Reference mark selector 

sensor position

P and Q limit switch sensor position

Offset 2.25 ±0.5

Selected 

IN-TRAC

 

™

 

reference mark

Mounting faces

Q limit magnet

P limit magnet

(Roll tol. ±0.5°)

0.08

13.5

8.75 

*

4.25

4.15

10

0.25

7.8

7.8

5 

†

Optical centreline  

(incremental and reference mark)

Optical centreline marker

18

R > 30 Dynamic bend radius 
R > 10 Static bend radius

35

23

11.5

6 min

Set-up LED

A

0.6

29

Detail A

Ø4.25 ±

0.25

Reference mark 
selector magnet

FASTRACK 

carrier 

thickness 0.4  
(including adhesive)

Forward direction of 

readhead relative to scale

*

 Extent of mounting face.   

†

 Dimension from substrate surface.

VIONiC readhead installation drawing

Dimensions and tolerances in mm

(Yaw tol. ±0.4°)

Rideheight 1.9 ±0.12

(Pitch tol. ±1°)

2 mounting holes M2.5 through, counterbored 

Ø3 × 2.3 deep both sides

 

NOTE: The recommended thread engagement 

is 5 min (7.5 including counterbore) and the 

recommended tightening torque is between  

0.25 and 0.4 Nm.

Содержание Vionic RTLC20/FASTRACK

















Отзывы:

Нет отзывов