Renesas IDT Tsi576 Скачать руководство пользователя страница 192 | Manualshive

Страница: 192 / 530

background image

8. Performance > Performance Monitoring

192

Tsi576 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

The following sub-sections describe the use of these parameters for monitoring the performance of the
serial RapidIO ports in Tsi576.

8.2.1

Traffic Efficiency

To characterize the efficiency of system traffic, the following parameters are used:

1.

Packet rate (number of packets / time)

— Packet rate is calculated using the number of packets computed from a counter register

configured to count the number of packets.

2.

Average packet size (number of 32-bit words / number of packets)

— Average packet size is calculated using a counter configured to count the number of 32-bit

words (call it COUNTER A), and a counter configured to count the number of packets (call it
COUNTER B). The average packet size is COUNTER A divided by the value in
COUNTER B.

3.

Utilization ((packet rate * packet size) / max capacity)

— Utilization is calculated using parameter 1 and parameter 2, above.

These values are derived from the number of packets and the number of 32-bit words on each interface.
The calculations of the packet rate, packet size, and utilization are completed externally.

8.2.2

Throughput

The count of packets per priority in each interface can be a very important parameter when debugging
RapidIO systems. This information can also be valuable when used by system software to dynamically
re-route traffic around congested interfaces. The following parameters are used to monitor the
throughput on each RapidIO interface:

•

Number of packets for each priority level (0, 1, 2 and 3)

— Each performance counter register (for example,

“RapidIO Port x Performance Statistics

Counter 0 Register” on page 346

) can be configured to count the number of packets selected

based on priority.

Retried packets are not counted.

«
...
190
191
192
193
194
...
»

Содержание IDT Tsi576



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IDT Tsi576

Бренд: Amped Wireless Страницы: 22

Бренд: YA Страницы: 47

Бренд: Holland Страницы: 4

Бренд: Sarowin Страницы: 9

Бренд: Accton Technology Страницы: 547

Бренд: Uniclass Страницы: 32

Бренд: Jerguson Страницы: 16

Liquipoint FTW33

Бренд: Endress+Hauser Страницы: 48

Бренд: Ubiquiti Страницы: 14

Summit X450-G2-24t-GE4

Бренд: Extreme Networks Страницы: 2

Бренд: Comnet Страницы: 105

Бренд: Pakedge Device & Software Страницы: 8

iMatrix H44H150

Бренд: infobit Страницы: 27

TU2-700 - DATA SHEETS

Бренд: TRENDnet Страницы: 9

Бренд: EG Страницы: 22

Бренд: Icy Box Страницы: 24

Бренд: Microsens Страницы: 11

ADDERView Secure AVS-4128

Бренд: ADDER Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды