REMKO WSP 110 Скачать руководство пользователя страница 48

Страница: 48 / 52

No.

Designation

WSP 80/110/140/180

Terminal strips

On request, please specify

the serial number

Smart Control Touch operating panel

Pressure sensor suction side/low pressure

Pressure sensor pressure-side/high pressure

Heat gas probe

Probe suction-side

Carel heating return/inlet heat pump probe

SMT PT1000 heating inlet SMT probe

Carel heating inlet/outlet heat pump probe

Carel inlet brine probe

Brine insulation shell, plate heat exchanger

Spare parts not illustrated

SMT PT1000 brine return flow probe

On request, please specify

the serial number

SD card

(current software without Smart Web, Smart Count)

Connection cable for pressure sensors

Code resistance 200/240/300/360 Ohm

Red indicator light for REMKO Smart Serv

Carel additional circuit board

To assure the correct delivery of spare parts, please always provide the unit type with its corresponding

serial number (see name plate).

Components of fittings set (without illustration)

Designation

WSP 80/110/140/180

Fittings set, complete

On request, please specify

the serial number

Immersion probe

Dirt trap

Ball valve 1“, red

Ball valve 1“, blue

Safety assembly

External probe

To assure the correct delivery of spare parts, please always provide the unit type with its corresponding

serial number (see name plate).

REMKO series WSP

Содержание WSP 110





















































Результаты поиска

Содержание WSP 110

Отзывы:

REMKO WSP 110, Руководство по сборке и эксплуатации, Страница: 48 / 52

Результаты поиска

Содержание WSP 110

Отзывы: