background image

Important Safe Operation Practices

1

2

Training

1. 

Read, understand, and follow all instructions on the machine and 

in the manual(s) before attempting to assemble and operate. Keep 

this manual in a safe place for future and regular reference and for 

ordering replacement parts. 

2. 

Be familiar with all controls and their proper operation. Know how 

to stop the machine and disengage them quickly.

3. 

Never allow children under 14 years of age to operate this 

machine. Children 14 and over should read and understand the 

instructions and safe operation practices in this manual and on 

the machine and be trained and supervised by an adult. 

4. 

Never allow adults to operate this machine without proper 

instruction. 

5. 

Thrown objects can cause serious personal injury. Plan your snow-

throwing pattern to avoid discharge of material toward roads, 

bystanders and the like. 

6. 

Keep bystanders, pets and children at least 75 feet from the 

machine while it is in operation. Stop machine if anyone enters 

the area.

7. 

Exercise caution to avoid slipping or falling, especially when 
operating in reverse.

Preparation

Thoroughly inspect the area where the equipment is to be used. Remove 

all doormats, newspapers, sleds, boards, wires and other foreign objects, 

which could be tripped over or thrown by the auger. 
1. 

Always wear safety glasses or eye shields during operation and 

while performing an adjustment or repair to protect your eyes. 

Thrown objects which ricochet can cause serious injury to the 

eyes.

2. 

Do not operate without wearing adequate winter outer garments. 

Do not wear jewelry, long scarves or other loose clothing, which 

could become entangled in moving parts. Wear footwear which 

will improve footing on slippery surfaces. 

3. 

Use a grounded three-wire extension cord and receptacle for all 

machines with electric start engines. 

4. 

Adjust auger housing height to clear gravel or crushed rock 

surfaces. 

5. 

Disengage all control levers before starting the engine. 

6. 

Never attempt to make any adjustments while engine is running, 

except where specifically recommended in the operator’s manual.

7. 

Let engine and machine adjust to outdoor temperature before 
starting to clear snow. 

Safe Handling of Gasoline

To avoid personal injury or property damage use extreme care in 

handling gasoline. Gasoline is extremely flammable and the vapors are 

explosive. Serious personal injury can occur when gasoline is spilled on 

yourself or your clothes which can ignite.  Wash your skin and change 

clothes immediately.
1. 

Use only an approved gasoline container.

2. 

Extinguish all cigarettes, cigars, pipes and other sources of 

ignition.

3. 

Never fuel machine indoors. 

4. 

Never remove gas cap or add fuel while the engine is hot or 

running. 

5. 

Allow engine to cool at least two minutes before refueling.

6. 

Never over fill fuel tank. Fill tank to no more than ½ inch below 

bottom of filler neck to provide space for fuel expansion.

7. 

Replace gasoline cap and tighten securely.

8. 

If gasoline is spilled, wipe it off the engine and equipment. Move 

machine to another area. Wait 5 minutes before starting the 

engine.

9. 

Never store the machine or fuel container inside where there is an 

open flame, spark or pilot light (e.g. furnace, water heater, space 

heater, clothes dryer etc.). 

10. 

Allow machine to cool at least 5 minutes before storing.

11. 

Never fill containers inside a vehicle or on a truck or trailer bed 

with a plastic liner. Always place containers on the ground away 

from your vehicle before filling.

12. 

If possible, remove gas-powered equipment from the truck or 

trailer and refuel it on the ground. If this is not possible, then 

refuel such equipment on a trailer with a portable container, 

rather than from a gasoline dispenser nozzle.

13. 

Keep the nozzle in contact with the rim of the fuel tank or 

container opening at all times until fueling is complete. Do not use 
a nozzle lock-open device.

Operation

1. 

Do not put hands or feet near rotating parts, in the auger housing 

or chute assembly. Contact with the rotating parts can amputate 

hands and feet. 

2. 

The auger control lever is a safety device. Never bypass its 

operation. Doing so makes the machine unsafe and may cause 

personal injury. 

3. 

The control levers must operate easily in both directions and 

automatically return to the disengaged position when released. 

4. 

Never operate with a missing or damaged chute assembly. Keep 

all safety devices in place and working.

WARNING! 

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or 

property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to 

comply with these instructions may result in personal injury. When you see this symbol. 

HEED ITS WARNING!

DANGER: 

This machine was built to be operated according to the safe operation practices in this manual. As with any type of power 

equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating fingers, 

hands, toes and feet and throwing foreign objects. Failure to observe the following safety instructions could result in serious injury or 

death.

CALIFORNIA PROPOSITION 65

WARNING! 

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of 

California to cause cancer and birth defects or other reproductive harm.

Содержание 500

























Отзывы: