Remii WM-45-XS, Инструкция по установке и эксплуатации

Страница: 6 / 23

UNPACKING AND TESTING APPLIANCE
Carefully remove the appliance from the box.
Prior to installing the appliance, test to make sure the appliance operates properly by plugging
the power supply cord into a 120 Volt grounded outlet.
Test all aspects of its operation (manual switches, remote and heater) to make sure all
components are operating correctly.
As with most electronic devices, your new electric fireplace has been designed to operate at
temperatures between 5
℃ (41 ℉
fireplace to reach room temperature before turning it on.
NOTE: There may be trace of odor during the first few minutes of initial use. This is
harmless, normal and will never occur again.
GROUNDING APPLIANCE
This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as
shown in (C) is available for connecting three
receptacles. The green grounding lug extending from the a
permanent ground such as a properly grounded outlet box. The adapter should not be used if a
three-slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove plug from outlet.
LOCATING THE FIREPLACE
Plan where to locate and frame the fireplace. This will save time and money later when you
install the fireplace. Before installation consider the following:
1. Where the fireplace is located must allow for wall and ceiling
2. Consider a location where the fireplace screen will not be exposed to direct sunlight from
windows or doors.
3.
A 15 ampere, 120 Volt, 60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch circuit
to trip of fuses to blow.
6
UNPACKING AND TESTING APPLIANCE
Carefully remove the appliance from the box.
he appliance, test to make sure the appliance operates properly by plugging
the power supply cord into a 120 Volt grounded outlet.
Test all aspects of its operation (manual switches, remote and heater) to make sure all
components are operating correctly.
As with most electronic devices, your new electric fireplace has been designed to operate at
℉ ) and 3 5 ℃ (95 ℉ ). During the cold winter months, allow the
fireplace to reach room temperature before turning it on.
NOTE: There may be trace of odor during the first few minutes of initial use. This is
harmless, normal and will never occur again.
This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as
shown in (C) is available for connecting three-blade grounding type plugs to two
receptacles. The green grounding lug extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box. The adapter should not be used if a
slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove plug from outlet.
LOCATING THE FIREPLACE
Plan where to locate and frame the fireplace. This will save time and money later when you
install the fireplace. Before installation consider the following:
Where the fireplace is located must allow for wall and ceiling clearances
Consider a location where the fireplace screen will not be exposed to direct sunlight from
A 15 ampere, 120 Volt, 60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch circuit should be provided to avoid circuit breakers
he appliance, test to make sure the appliance operates properly by plugging
Test all aspects of its operation (manual switches, remote and heater) to make sure all
As with most electronic devices, your new electric fireplace has been designed to operate at
). During the cold winter months, allow the
NOTE: There may be trace of odor during the first few minutes of initial use. This is
This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as
blade grounding type plugs to two-slot
dapter must be connected to a
permanent ground such as a properly grounded outlet box. The adapter should not be used if a
To disconnect appliance, turn controls to off, then remove plug from outlet.
Plan where to locate and frame the fireplace. This will save time and money later when you
clearances
Consider a location where the fireplace screen will not be exposed to direct sunlight from
A 15 ampere, 120 Volt, 60 Hz branch circuit with proper ground must be available at the
should be provided to avoid circuit breakers