REMEHA Gas 320 Ace 285 Скачать руководство пользователя

Страница: 53 / 96

Tab.50 CU-GH13

Icon

Zone or function

Description

Internal DHW (Internal DHW)

Domestic hot water produced by boiler

CIRCA / CH

Central heating circuit

Commercial boiler

Gas boiler

Gas fired appliance

Gas boiler

Tab.51 Configuring a zone or function of CU-GH13 or SCB-02

Parameters, counters, signals

Description

Parameters

Set the parameters at installer level

Counters

Read the counters at installer level

Signals

Read the signals at installer level

Adv. Parameters

Set the parameters at advanced installer level

Adv. Counters

Read the counters at advanced installer level

Adv. Signals

Read the signals at advanced installer level

8.3

List of parameters

8.3.1

CU-GH13 control unit settings - Gas 320 Ace

All tables show the factory setting for the parameters.

Important

The tables also list parameters that are only applicable if the boiler

is combined with other equipment.

Tab.52 Navigation for basic installer level

Level

Menu path

Basic installer

> Installation Setup > CU-GH > Submenu

(1)

> Parameters, counters, signals > Parameters

(1) See the column "Submenu" in the following table for the correct navigation. The parameters are grouped in specific functionalities.

Tab.53 Factory settings at basic installer level

Code

Display text Description

Adjustment range

Subme

285

355

430

500

575

650

AP016

CH function

Enable central heating

heat demand processing

0 = Off

1 = On

Gas

fired ap

pliance

AP017

DHW func

tion on

Enable domestic hot water

heat demand processing

0 = Off

1 = On

Gas

fired ap

pliance

AP074

Force sum

mer mode

The heating is stopped.

Hot water is maintained.

Force Summer Mode

0 = Off

1 = On

Outdoor

tempera

ture

CP000

MaxZoneT

FlowSet

point

Maximum Flow Tempera

ture setpoint zone

7 - 100 °C

Direct

zone

CP010

Tflow set

point zone

Zone flow temperature

setpoint, used when the

zone is set to a fixed flow

setpoint.

7 - 100 °C

Direct

zone

CP080

User

T.Room Ac

tivity

Room setpoint tempera

ture of the user zone activ

ity

5 - 30 °C

Direct

zone

8 Settings

7734324 - v.03 - 29092020

Содержание Gas 320 Ace 285

































































































Результаты поиска

Содержание Gas 320 Ace 285

Отзывы:

Похожие инструкции для Gas 320 Ace 285

Бренды по названию

Популярные бренды

REMEHA Gas 320 Ace 285, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Gas 320 Ace 285

Отзывы:

Похожие инструкции для Gas 320 Ace 285

Бренды по названию

Популярные бренды