background image

3

91772

INSTALLATION INSTRUCTIONS

1. Locate the dispenser indoors on a level counter top.

COUNTER MOUNTING

The ice dispenser

must be sealed

to the counter. The template drawing indicates openings which must be

cut in the counter. Locate the desired position for the dispenser, then mark the outline dimensions on the

counter using the template drawings. Cut openings in the counter.

Apply a continuous bead of NSF

International

(NSF) listed silastic sealant (Dow 732 or equal) approximate-

ly 1/4”inside of the unit outline dimensions and around all openings. Then position the unit on the counter

within the outline dimensions. All excess sealant must be wiped away immediately.

2. The beverage tubes, drain line and power cord are routed through the large opening in the bottom of the

unit. See the MOUNTING TEMPLATE, for locating the required clearance hole in the counter for these util-

ity lines.

3. SINK DRAIN ASSEMBLY: Connect the drain tube to an open drain. Additional drain tubing is provided with

the unit. The drain line must continuously pitch downward away from the unit and contain no “traps”or im-

proper drainage will result.

A. Use tube, clamp and insulation provided to assemble drain.

B. To assure proper drainage, do not allow “trap”to form in drain line. Be sure drain line runs flat with

bottom of dispenser.

4. Connect the beverage system product lines as indicated in Figure 2 (and in Figure 3 for cold plate units).

This work should be done by a qualified service person. Note that the hoses are marked with numbers ( 1

through 4 or 5) for

syrup connections

On 5 valve “-BC”units, the plain water is marked “NON CARB

WATER”.

5. Clean the hopper interior (see CLEANING INSTRUCTIONS).

6. Connect the power cord to a 120 volt, 60 cycle, 3-wire grounded receptacle.

NOTE:

Water pipe connections and fixtures directly connected to a potable water supply shall be

sized, installed and maintained according to Federal, State and Local Laws/

DRAIN LINE

STAINLESS STEEL ELBOW

DRAIN TUBING PROVIDED

WITH DISPENSER

DISPENSER BOTTOM

Содержание DB90S-BC






























Отзывы: