Reliance FX920, Инструкция по установке и эксплуатации, Руководство пользователя, Страница: 12 / 32

4. PROGRAMMING THE CHAIR
The items described in Section 4. are built-in features of the
chair. Only those users who wish to utilize these features need
to be concerned with this Section. The chair will operate as
previously designed if these features are not used. The chair
can be programmed in the same fashion from either switch
located on the chair back.
4.1. Safety/Shutdown Feature
The chair has a built-in Safety/Shutdown feature. This feature
causes the chair to shutdown or become inoperable. This
feature prevents unauthorized use of the chair. (See Figure
2).
4.1.1 To ENTER Safety/Shutdown Mode
4.1.1.1 Depress and HOLD either STOP switch.
4.1.1.2 With the STOP switch depressed, depress the
LOWER BASE switch on the same side of the chair back.
4.1.1.3 A two second beep will be heard to indicate the chair
will NOT move if any additional switches are depressed.
4.1.1.4 The LED’s on the Membrane Switches will blink every
three seconds while in Safety/Shutdown Mode.
4.1.2 To EXIT Safety/Shutdown Mode, repeat the
above sequence.
4.1.2.1 Depress and HOLD either STOP switch.
4.1.2.2 With the STOP switch depressed, depress the LOWER
BASE switch on the same side of the chair back.
4.1.2.3 A two second beep will be heard to indicate the chair
is functional, and movement of the chair WILL OCCUR when
another switch is depressed.
4.1.2.4 The LED’s will come back on when the chair becomes
operational.
4.2. Individual Programming of the RAISE TOP,
RECLINE TOP, RAISE BASE, and LOWER
BASE switch located on the Chair Back or
Footswitch. (See Figure 2 & 3).
4.2.1 These individual switches may be programmed to
function in two ways. If the movement of the chair STOPS
when the switch is released, this is called the MOMENTARY
MODE of operation. If the movement of the chair continues
after the switch is released, this is called the MAINTAINING
MODE of operation. The factory designed setting for the
RAISE TOP and RECLINE TOP switches located on the chair
top is MAINTAINING MODE. The factory designed setting for
the RAISE BASE and LOWER BASE switches located on the
chair top is MOMENTARY MODE. If changed, the new settings
will remain permanent as long as main power remains applied
to the chair and will apply to the similar function on the other
side.
4.2.2 To change these settings the chair must be placed in
Setup Mode. Once in Setup Mode, depressing one of these
switches will change its present setting from MOMENTARY
to MAINTAINING or from MAINTAINING to MOMENTARY.
Depressing a switch repeatedly will cause the setting to toggle
between the two modes of operation.
4.2.3 To ENTER Setup Mode and change current
settings
4.2.3.1 Depress and HOLD either STOP switch.
4.2.3.2 With the STOP switch depressed, depress the AUTO
switch on the same side of the chair back.
4.2.3.3 A one second beep will be heard to indicate you
have ENTERED Setup Mode. The LED’s will blink on and off
while in Setup Mode.
4.2.3.4 Depress any of the following switches (including
footswitch), one at a time, to toggle its current setting - RAISE
TOP, RECLINE TOP, RAISE BASE, OR LOWER BASE. When
the switch is depressed, a SHORT beep (0.25 seconds) will
indicate the switch is now in MOMENTARY MODE of operation.
A LONG beep (1.05 seconds) will indicate the switch is now
in MAINTAINING MODE of operation.
4.2.3.5 When finished programming the chair, the chair MUST
be taken out of Setup Mode.
4.2.4 To EXIT Setup Mode, repeat steps 1 & 2
above.
4.2.4.1 Depress and HOLD either STOP switch.
4.2.4.2 With the STOP switch depressed, depress the AUTO
switch on the same side of the chair back.
4.2.4.3 A one second beep will be heard to indicate the chair
has EXITED Setup Mode. The LED’s will come back on.
IN-FX920 12