Reliable Controls MACH-Air Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 44

Reliable Controls MACH-Air Скачать руководство пользователя страница 20

14

MACH-Air™ VAV Controller



2002 Reliable Controls™ Corporation

Workstation Connection

Workstation Connection

Peer

The MACH-Air™ VAV controller is designed to be

programmed using a workstation running the RC-Studio™

software. The workstation must be connected to a MACH1™,

MACH2™,or MACH-Global™ controller, or ETHER-Net™

portal that resides on the same system as the MACH-Air™

VAV controller.

No EIA-232 port is available on

the MACH-Air™ VAV controller.

One way to access the

controller is through an EIA-

232 enabled controller on the

same system (as illustrated

below). An alternative is to use

the X-Port™ converter through

the SMART-Net™ port as

discussed on the next page.

A MACH1™, MACH2™, or MACH-
Global™ controller, or ETHER-
Link™ portal must be configured
as address one in the system.
(See MACH-Air™ Real Time Clock)

MACH1

™

MACH-Air

™

Operator Workstation

Peer Communications

«
...
18
19
20
21
22
...
»

Содержание MACH-Air













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды