Reinhardt MWS 10 Скачать руководство пользователя страница 95

Страница: 95 / 141

REINHARDT

System- und Messelectronic GmbH

Bergstr. 33 86911 Diessen-Obermühlhausen Postfach 12 41 D-86908 Diessen Tel. 08196 - 934100

MWS_55_e.indb Page 95

geändert am 04.12.2020 von DO

Manual MWS 55 / MWS 88 / MWS 10 and Sensors 55

to table of contents

8.2.1.4 Protocoll-Select (CAUTION)

Controlling the interface (Protocol select)

CAUTION: THESE SETTINGS ARE VERY CRITICALLY!!

!S<DZ><#13>

Suppresses inter alia the output of data

DZ is the decimal value from the following binary listfor the different protocols.

Binary list of protocol parameters for DZ.

DZ (binary) =

xxxxxx00b (bit 1+2) : RS232 - MWS sends a datastring each second

xxxxxx01b (bit 1+2) : RS422 - MWS sends a datastring each second

xxxxxx10b (bit 1+2) : RS485 - MWS is addressed and sends data only on request

xxxxxx11b (bit 1+2) : Reserved

xxxxx1xxb (bit3) : MWS sends data only on request (RS232 + RS422)

xxxx1xxxb (bit4) : MWS sends data on request and when storing into the logger

xxxXxxxxb (bit5) : Reserved

xxXxxxxxb (bit6) : Reserved

x1xxxxxxb (bit7) : Sends check byte(bit 1+2

≠

11), simple XOR or CRC-8 (Bit21=1)

1xxxxxxxb (bit8) : Flash write protection. (Commands changing the data flash are

rejected (except update))

This mode only can be cancelled in SECURE-Mode!

xxxxxxxx 1xxxxxxx xxxxxxxxb (bit16)

: Suppresses reset outputs on the GPS / RS-232 port, which are

sent by default since V3.0222

xxxxxxx1 xxxxxxxx xxxxxxxxb (bit17)

: Standard protocol: Sets RS-485 full duplex to suppress the

waiting time in "normal" RS-485 mode (half duplex) (since V3.0240)

xxxxxx1x xxxxxxxx xxxxxxxxb (bit18)

: Prevents the port from disabling (since V3.0244)

Imortant when operating at a MOBOTIX cam!

xx1xxxxx xxxxxxxx xxxxxxxxb (bit22)

: MWS 5MV compatibility mode (data each 2 seconds)

By adding of single binary values the parameters can be combined.

Example for MWS with RS422 only sends on request:

for RS422 (binary) = xxxxxx01 (DZ=1)

for sending on request (binary) = xxxxx1xx (DZ=4)

added --> = xxxxx101 --> decimal = 5 --> !S5<#10>

CAUTION: With RS485 the WSA's address must always follow on ! or ?, for otherwise the com-

mand won't be recognized! (Standard@ = 10)

!S+<Bit#><#13> ;

Set single bit in protocol select

!S-<Bit#><#13> ;

Set back single bit in protocol select

Example: !S+3 activates sending data on request and when storing.

CAUTION! Never use this command with analog display connected!!!

Содержание MWS 10














































































































































Результаты поиска

Содержание MWS 10

Отзывы:

Похожие инструкции для MWS 10

Бренды по названию

Популярные бренды

Reinhardt MWS 10, Руководство пользователя

Результаты поиска

Содержание MWS 10

Отзывы:

Похожие инструкции для MWS 10

Бренды по названию

Популярные бренды