background image

Page 1

Instrument Storage

Cover the probe tip with an Ocu-Film Tip Cover for protection.

If the TONO-PEN VET unit is not to be used until a subsequent day, the 

instrument and accessories should be replaced in the storage case provided.

If the TONO-PEN VET unit is not to be used for an extended period of time, 

remove the batteries from the instrument. 

Maintenance Procedures

 

Maintenance that should be performed on the TONO-PEN VET consists of activities 

such as protecting the probe tip, keeping surfaces free of dust and dirt and storing in 

a dry and cool place so as not to adversely affect electronic parts, and replacing the 

batteries.

Keep the probe tip protected with an Ocu-Film Tip Cover when in use or in storage. 

Avoid any contact with the probe tip when not protected by an Ocu-Film Tip Cover.

The probe post must be cleaned only with optical quality compressed gas before the 

first use each day, before instrument storage, in the event of unanticipated readings 

or if a “Good” calibration check cannot be obtained. To clean the probe post: 

Remove the Ocu-Film Tip Cover.

Spray the compressed gas onto the probe tip for approximately  seconds.

Wait 3 minutes to allow the instrument to thermally stabilize.

Cover the TONO-PEN VET unit’s probe tip with a new Ocu-Film Tip Cover.

TONO-PEN VET Body

Avoid any shock or excessive vibration which will damage the unit. Clean with a non-

abrasive, dry cloth. 

CAUTION 

dO NOT Immerse TONO-PeN veT bOdy IN FlUIds. ThIs WIll CAUse dAmAge 

TO The  eleCTrONICs ANd vOId The WArrANTy. 

Battery Replacement

The batteries need replacing when multiple beeps sound and “Lob” appears on the 

LCD upon depressing the activation switch. Occasionally, a noticeable slowing in the 

calibration check process or in activating the instrument for taking measurements 

may suggest that the batteries need replacing.  Always replace both batteries. Do not 

mix used and new batteries in the instrument. Reichert OCU-CEL XL batteries are 

recommended.

Note: The instrument will not function properly when mercury batteries are used.

1.

.

3.

1.

.

3.

4.

Maintenance & Storage

Содержание TONO-PEN VET






















Отзывы: