Regency PANORAMA P33E Скачать руководство пользователя страница 1

Страница: 1 / 64

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-394b

MODELS: P33E-NG10 Natural Gas P33E-LP10 Propane

06.29.16

Tested by:

Installer

: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner:

Please keep these instructions for future reference.

www.regency-fire.com

Owners &

Installation Manual

Panorama

P33E Zero Clearance

Direct Vent Gas Fireplace

P33 Video

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS
•

Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach you gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

Содержание PANORAMA P33E

































































Результаты поиска

Содержание PANORAMA P33E

Отзывы:

Похожие инструкции для PANORAMA P33E

Бренды по названию

Популярные бренды

Regency PANORAMA P33E, Инструкция для владельца и по установке

Результаты поиска

Содержание PANORAMA P33E

Отзывы:

Похожие инструкции для PANORAMA P33E

Бренды по названию

Популярные бренды