background image

Rigid Pipe Venting

Horizontal or Vertical Terminations

Venting Arrangements - Vertical  
Terminations

Rigid Pipe System

(Propane & Natural Gas)

Two 45° elbows = One 90° elbow

The P40 is approved for a maximum 40 ft. straight vertical, with 

Rigid 

Pipe

 vent systems for Propane and Natural Gas. 

The diagram to the right shows allowable combinations of straight vertical 
and offset to vertical terminations with 

Rigid Pipe

 vent systems for 

Propane and Natural Gas. Maximum two 90° elbows allowed. 

The unshaded area in the diagram shows allowable venting 
confi gurations with the Vent Restrictor Factory Set.

The lightly shaded area, 

0

2

4

6

40

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

6

8

2

0

4

10

12

16

18

14

20

26

28

22

24

30

, in the diagram shows all allowable venting 

confi gurations with the Vent Restrictor on Set 1.

The darker shaded area, 

0

2

4

6

40

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

6

8

2

0

4

10

12

16

18

14

20

26

28

22

24

30

, in the diagram shows allowable venting 

confi gurations with the Vent Restrictor on Set 2.

•  

Vent must be supported at offsets.  

•  

Horizontal sections must be supported every 3 feet

•  

Firestops are required at each floor level and whenever 
passing through a wall.

•  

Maintain clearances to combustible materials.

•  

Minimum of 1’ pipe section between any elbows.

Note:  Must use optional rigid pipe adapter when using Rigid Pipe 

(Part # 770-994).

Maximum:

40

ft.

(12.2m)

Minimum

8

’9”

(2.6m)

Max. 10’ (3m)(centerline to centerline)

Minimum 12” (305mm)

Maximum:

28

ft.

(8.5m)

0

2

4

6

40

8

10

12

14

16

18

20

22

24

26

28

30

V

ertical

Height

(Feet)

32

34

36

38

6

8

2

0

4

10

12

12

16

18

14

20

26

28

22

24

30

Vent Restrictor on Set 1

Vent Restrictor on Set 2

Vent Restrictor

Factory Set

Rigid Pipe Adapter

(770-994)

Pipe Length

Vertical

Terminal

Storm Collar

Flashing

Ceiling Firestop

24" Pipe

Length

Adj.Pipe Length

11" - 14-5/8"

90 Elbow

o

AstroCap XL

Termination Cap

(946-623/P)

Wall Thimble

(required in Canada only)

Vinyl Siding

Standoff

P40 Gas Fireplace

If required by the external termination location the listed 
alternate termination caps may be used.  (Refer to Page 11)

Alternate Horizontal 

Termination Caps

Alternate Snorkel

Termination Cap

Part #1282 (14”)
Part #1281 (36”)

48

June 2007 Regency Product Specifi cations Book

Gas Fir

eplaces

Gas Fireplaces

Содержание P40-LP1








Отзывы: