Regency IP28 Gas Inbuilt Fireplace
33
33
INSTALLATION
OPERATING INSTRUCTIONS
COPY OF LIGHTING INSTRUCTION PLATE
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds
from your gas appliance. This is perfectly normal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listed below are some examples. All are
normal
operating sounds
and should not be considered
as defects in your appliance.
Fans:
.It is not unusual for the fan to make a "whirring"
sound when ON. This sound will increase or
decrease in volume depending on the speed
setting of your fan speed control.
This appliance is equipped with a combustion
and convection fan. These fans will operate as
soon a the appliance is turned on.
NOTE:
This appliance will not operate without
the convection fan running at all times.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a differ
-
ent gauge material from the rest of the firebox
and body. Therefore, the varying thicknesses of
steel will expand and contract at slightly different
rates which can cause "ticking" and "cracking"
sounds. You should also be aware that as there
are temperature changes within the unit these
sounds will likely re-occur. Again, this is normal
for steel fireboxes.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
RESETTING THE UNIT
If the appliance goes to 'lockout', the system
will have to be reset by unplugging or
pressing switch to OFF position.
*Important
: Wait at least 5 min for any
unburned gas to clear before resetting the
appliance.
NOTE:
Wait 2 minutes between reset
attempts.
WARNING:
DO NOT SPRAY AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHILE IN OPERATION.
"
Appliances incorporating a live fuel effect (designed to oper
-
ate with blue flames with slight yellow tips) may exhibit slight
carbon deposition."
FOR YOUR SAFETY READ BEFORE LIGHTING
A) BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the fl oor because
some gas is heavier than air and will settle on the
fl oor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance
- Do not touch any electric switch, do not use
any phone in your building
- Immediately call your gas supplier from a
neighbors phone. Follow the gas supplier’s
instructions.
- If you cannot reach your gas supplier, call the fi re
department.
B) Do not use this appliance if any part has been under
water. Immediately call a qualifi ed service technician
to inspect the appliance and to replace any part of
the control system and any gas control which has
been under water.
This appliance needs fresh air for safe operation and
must be installed so there are provisions for adequate
combustion and ventilation air.
918-958
WARNING: If you do not follow these
instructions exactly, a fi re or explosion
may result causing property damage,
personal injury or loss of life. Improper
installation, adjustment, alteration, service
or maintenance can cause injury or property
damage. Refer to the owner’s information
manual provided with this appliance. For
assistance or additional information consult
a qualifi ed installer, service agency or gas
supplier.
LIGHTING INSTRUCTIONS
TO TURN OFF GAS APPLIANCE
This appliance must be installed in accordance
with local codes, if any; if not,
follow the current CAN1-B149/ANSI Z 223.1
(Australia: AS5601-2004, New Zealand: NZS
5261)
DO NOT REMOVE THIS
INSTRUCTION PLATE
Part #: 918-958
Colours:
Black on Grey, except for parts in RED
Size:
W 2.74" x H 12.45"
Sept. 22/10: created draft
Oct. 19/10 :revised size
1) Turn 3 way switch to OFF
2) Turn off all electric power to the unit if service
is to be performed.
CAUTION: Hot while in operation. Do not
touch. Severe Burns may result. Due to
high surface temperatures keep children,
clothing and furniture, gasoline and other
liquids having fl ammable vapors away. Keep
burner and control compartment clean.
See installation and operating instructions
accompanying appliance.
STOP! Read the safety information above on this
label.
1) Ensure the power cord is plugged into the
power outlet and turned on.
2) Turn 3 way switch to ON position
3) After approximately 60 seconds the spark
ignition system will spark for 5 seconds to
light the main burner.
4) If the main burner does not light, repeat step 2
to restart.
