background image

Regency IP28 Gas Inbuilt Fireplace

39

WARRANTY

Regency

®

 Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each 

unit thoroughly before it leaves our door. Regency® is pleased to extend this limited lifetime warranty to the  original purchaser of a Regency

®

 Product.

The Warranty:  

Lifetime

Covered under the agreement are the following components: The combustion chamber, heat exchanger, burner tubes/pans, logs, glass crystals, ceramic spa stones, 
pebbles, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime Warranty for fi ve (5) years for parts and labour and 
parts only thereafter.

External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and labour for one (1) year from the date of 
purchase and parts only thereafter.

Special Finishes - One year on stainless steel panels, nickel overlays, nickel faceplates, brushed nickel and antique copper full screens and doors. You can expect 
some changes in color as the product "ages" with constant heating and cooling. Regency warranties the product for any manufacturing defects on the original product. 
However, the manufacturers warranty does not cover changing colors and marks, ie. fi nger prints, etc applied after the purchase of the product. Damage from the use 
of abrasive cleaners is not covered by warranty.

Electrical components such as fans, switches, ignition modules, wiring, thermodiscs, remote control, thermopiles, thermocouples and gas valves are covered for one 
year for parts and labour from the date of purchase.

The warranty on brass parts is for one year, no labour. The brass is not warranted against tarnishing.

Repair/replacement parts purchased by the consumer from Regency

®

 after the original coverage has expired on the unit will carry a 90 day warranty valid with a receipt 

only.  Any item shown to be defective will be repaired or replaced at our discretion.  No labour coverage is included with these parts.

Conditions:

All installations must be performed by a qualifi ed gas fi tter and installed according to all applicable local and national codes.  Also, all service work must be carried out 
by a qualifi ed gas service person provided by the selling dealer.  It is the responsibility of the installer to ensure that the appliance is fi ring as per rating plate.  Any part 
or parts of this unit which in our judgement show evidence of such defect will be repaired or replaced at Regency

®

's option, through an accredited distributor or agent 

provided that the defective part be returned to the distributor or agent 

Transportation Prepaid,

 if requested. In areas where there is not an approved service agent or 

the closest approved service agent is situated more than thirty (30) kilometres from the installation, Regency is not obliged to arrange warranty repairs and travel and/
or additional labour charges will apply.

Porcelain/Enamel - Absolute perfection is neither guaranteed nor commercially possible.  Any chips must be reported and inspected by an authorised dealer within three 
days of installation.  Reported damage after this time will be subject to rejection.

It is the general practice of Regency

®

 to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to Regency 

and evaluated fro manufacturer defect.
At all times Regency reserves the right to inspect product in the fi eld which is claimed to be defective.

All claims must be submitted to Regency

®

 by authorised selling dealers.  It is essential that all submitted claims provide all of the necessary information including customer 

name, purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.

Exclusions:

This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.  It does not cover installation and operational related problems such as 
over-fi ring, downdrafts or spillage caused by environmental conditions, nearby trees, buildings, hilltops, mountains, inadequate fl ueing or ventilation, excessive offsets, 
negative air pressures caused by insuffi cient make up air, mechanical systems such as furnaces, fans, clothes dryers etc.

Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.

Regency

®

 will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.

Performance problems due to operator error will not be covered by this warranty policy.

The warranty does not extend to any part or parts which show evidence of misuse or abuse, neglect, accident, lack of maintenance, or improper installation.

Products made by other manufacturers and used in conjunction with the operation of this appliance without authorisation from Regency

®

, may nullify your warranty on 

this product.

Regency shall in no event be liable for any special, indirect consequential damages of any nature whatsoever which are in excess of the original purchase price of the 
product. Any alteration to the unit which causes sooting or carboning that results in damage to the exterior facia is not the responsibility of Regency Fireplace Products.

SUBJECT TO CHANGE.

DISTRIBUTORS:

Western Australia

Eastern Australia

Air Group Australia

Fireplace Products Australia PTY. Ltd.

28-30 Division St.

21-23 South Link Blvd.

Welshpool, WA   6106

Dandenong, VIC 3  175

08 9350 2200

03 9799 7277

NOTE: PLEASE  RETAIN YOUR INVOICE AS PROOF OF PURCHASE FOR WARRANTY 

VERIFICATION

INCORRECT INSTALLATION OR GAS PRESSURE SETTINGS ARE NOT COVERED BY 

WARRANTY

A SERVICE OR CALLOUT FEE WILL BE CHARGED IN THESE CIRCUMSTANCES.

Содержание IP28-LPG









































Отзывы: