Regency Grandview G600C Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 104

background image

28

|

Grandview

®

G600C Gas Fireplace

installation

Chase Vent Installation - Cool Wall (Part #776-941)

08.25.20

920-301

G600EC/G600C

1

08.11.20

920-150

G600EC

1

29

Ceiling

Max 2” (51 mm)

Ceiling

Max 2” (51 mm)

Side View

Top of enclosure

CHASE VENT INSTALLATION—COOL WALL

(PART #776-941)

Framed opening must be at least 2 3/8” (60 mm) tall, and at least 29 3/8” (746 mm) wide to accomodate the chase vent. The
top of the chase vent opening must be 2” (51 mm) or less from the top of the chase enclosure. Fasten the chase vent with
screws and construction adhesive.

If the chase vent is not being used, a minimum 58 in

2

(374 cm

2

) opening in the enclosure is required to maintain safe operating

temperatures. This can be achieved in a number of ways including a reveal at the top of the chase.

08.11.20

920-150

G600EC

1

29

Ceiling

Max 2” (51 mm)

Ceiling

Max 2” (51 mm)

Side View

Top of enclosure

(746 mm)

(60 mm)

«
...
26
27
28
29
30
...
»

Содержание Grandview G600C









































































































Отзывы:

Нет отзывов

Похожие инструкции для Grandview G600C

Бренд: Valor Страницы: 4

Бренд: Faber Страницы: 8

e-MatriX 800-500 I

Бренд: Faber Страницы: 12

Бренд: Waterford Страницы: 24

ECO-prestige 75

Бренд: KAL-FIRE Страницы: 184

Бренд: HAMPTON BAY Страницы: 36

Бренд: Be Modern Страницы: 8

Бренд: Majestic Страницы: 20

Бренд: Vantage Hearth Страницы: 40

Бренд: Paramount Fitness Страницы: 56

Бренд: Majestic Страницы: 9

Бренд: Napoleon Страницы: 2

Бренд: HomeTech Страницы: 6

Бренд: Home Decorators Collection Страницы: 30

Бренд: Looft Industries Страницы: 16

Бренд: Barbecook Страницы: 11

DRT4000-C Series

Бренд: Superior Fireplaces Страницы: 80

Бренд: Nordpeis Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды