background image

 

F2450M Regency Freestanding Woodstove

  |    

29

maintenance

Ways to Prevent and Keep Unit 
Free of Creosote

1.  Burn  stove  with  the  draft  control  wide  open 

for about 10-15 minutes every morning during 
burning season.

2.  Burn stove with draft control wide open for about 

10 - 15 minutes every time you apply fresh wood. 
This allows the wood to achieve the charcoal 
stage faster and burns up any unburned gas 
vapours which might otherwise be deposited 
within the system.

3.  Only burn seasoned wood! Avoid burning wet 

or green wood. Seasoned wood has been dried 
at least one year.

4.  A small hot fire is preferable to a large smoul-

dering one that can deposit creosote within the 
system.

5.   Establish a routine for the fuel, wood burner 

and firing technique. Check daily for creosote 
buildup.

6.  The  chimney  and  chimney  connector  should 

be inspected at least once every two months 
during  the  heating  season  to  determine  is  a 
creosote buildup has occurred.

7. 

Have chimney system and unit cleaned by 
competent chimney sweeps twice a year 
during the first year of use and at least once 
a year thereafter or when a significant layer 
of creosote has accumulated (3 mm/1/8" or 
more) it should be removed to reduce the 
risk of a chimney fire. 

Door Gasket

If the door gasket requires replacement 7/8" diameter 
material must be used. Regency uses a 7/8" gasket 
rope (Part #846-570). A proper high temperature 
gasket adhesive is required.  See your Regency 
Dealer.

The door catch may require adjustment as the door 
gasket compresses after a few fires.  The door latch 
compression may require adjustment to renew seal. 
Removal of a shim, (see section in this manual), 
will allow the latch to be moved closer to the door 
frame, causing a tighter seal.  

 

Glass Maintenance

Your Regency stove is supplied with 5mm  Neoceram 
ceramic glass (Part #846-306) that will withstand the 
highest heat that your unit will produce.  In the event 
that you break your glass by impact, purchase your 
replacement from an authorized Regency dealer 
only,  and  follow  our  step-by-step  instructions  for 
replacement (refer to Glass Replacement section).

Allow the stove to cool down before cleaning the 
glass. Cleaning the glass will prevent build up of 
carbon and allow full view of the fire.
  

Wood Storage

Store wood under cover, such as in a shed, or cov-
ered with a tarp, plastic, tar paper, sheets of scrap 
plywood, etc., as uncovered wood can absorb water 
from rain or snow, delaying the seasoning process.

Maintenance

It is very important to carefully maintain your fire-
place stove, including burning seasoned wood and 
maintaining a clean stove and chimney system. Have 
the  chimney  cleaned  before  the  burning  season 
and as necessary during the season, as creosote 
deposits may build up rapidly. Moving parts of your 
stove require no lubrication.

Creosote

When wood is burned slowly, it produces tar and 
other  organic  vapours  combine  with  moisture  to 
form creosote. The creosote vapours condense in 
the relatively cool chimney flue of a slow burning 
fire. As a result, creosote residue accumulates on 
the  flue  lining.    When  ignited,  this  creosote  can 
result in an extremely hot fire.

The  chimney  connector  and  chimney  should  be 
inspected at least once every two months during 
the heating season to determine if creosote build 
up  has  occurred.  If  creosote  has  accumulated  it 
should be removed to reduce the risk of chimney fire.

CAUTION:  Things to remember in case of 
a chimney fire:

1. Close all draft and damper controls.

2. CALL THE FIRE DEPARTMENT.

WARNING:

 Do not clean the glass when it is hot.

WARNING: 

Do not use abrasive cleaners, a damp 

cloth and glass cleaner is effective.

WARNING

: Do not use substitute materials.

WARNING

: Do not abuse the glass door, such as 

striking of slamming shut.

WARNING

: Do not operate with broken glass.

Содержание Cassic F2450













































Отзывы: