Regency Cassic F2450 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 44

background image

16

|

F2450M Regency Freestanding Woodstove

installation

Mobile Home Kit - for Canada

Note: The optional ashdrawer cannot be used when using the Mobile Home Kit.

920-167

28.10.19

F2450

Mobile Home Kit - For Canada

Note: The optional ash drawer cannot be used when using the Mobile Home Kit.

3.

Remove the 4" knock out from the rear pedestal.

4.

Install rear collar to the rear pedestal using 4 screws.

Page 1 of 1

075-500.SLDASM

12/19/2016

Mobile Home Box

Pedestal Stove

Collar

Flex

The Mobile Home kit contains:

1 Bottom metal cover - only used when air is drawn from the floor.
1 Flex
1 Collar
1 Mobile home box
1 Square transition box (used when installing bottom heat shield/

legs)

Screws

5.

Attach flex to rear pedestal using supplied screws or the 4" clamp.

6. Bring pedestal base near the base of the firebox and secure flex

to the Mobile Home box.

7. Secure pedestal base and Mobile Home Box to firebox as shown

in diagram 3 using the screws that were previously removed/
loosened in step 1. See pedestal instructions.The Mobile Home
Box and firebox use the same screws.

Diagram 4

8.

Install blanking plate to the front of the pedestal with 4 screws.

1.

Lay unit on its back. Remove two front 7/16 bolts. Loosen rear
two 7/16" bolts. See diagram 1.







Install rear collar
to the rear pedes-
tal using 4 screws

.

Diagram 2

Diagram 3

4 screws

Diagram 5

9.

Place unit into position and install the mandatory outside air kit.

See «Mobile Home installation» section in this manual.

Blanking

plate

2.

If using outside air from the rear of the pedestal, follow instruc-
tions noted below. If using outside air from the pedestal base,
follow instructions from step 10 to 16. For bottom heat shield/
legs, follow instructions from step 17 to 22. The Mobile Home Box
is always mounted in between the firebox and pedestal or bottom
heat shield.

Diagram 1

«
...
14
15
16
17
18
...
»

Содержание Cassic F2450













































Отзывы:

Нет отзывов

Похожие инструкции для Cassic F2450

Бренд: Palazzetti Страницы: 12

Бренд: Austroflamm Страницы: 49

Studio Stove 14

Бренд: Warmington Страницы: 16

Бренд: TONWERK Страницы: 14

Бренд: CombiSteel Страницы: 18

Бренд: Harman Страницы: 18

Бренд: HDG Страницы: 64

Бренд: Harman Stove Company Страницы: 38

Naphtha 533 Series

Бренд: Coleman Страницы: 25

Бренд: Coleman Страницы: 28

Бренд: Drolet Страницы: 39

Ecofire Anita 12

Бренд: Palazzetti Страницы: 12

Бренд: Travis Industries Страницы: 2

Бренд: Travis Industries Страницы: 4

Бренд: Aarrow Страницы: 32

Ecoburn Plus 4 BK061a

Бренд: Aarrow Страницы: 34

Бренд: Kalor Страницы: 24

Бренд: WANDERS Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды