Regency Alterra CS1200 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 32

background image

Regency CS1200 Freestanding Wood Stove

21

INSTALLATION

1)

Remove

the

fi ve screws from the back panel of the unit - to remove the

fan cover plate.

2)

Slide the fan up into the rear heat shield.

3)

After aligning holes, secure the fan to the rear heat shield using the fi ve

screws removed earlier.

4)

Secure the bottom of the fan using the two fan clips (in manual package)

and two bottom screws removed in step 1.

Note:

The connection cord should not be in contact with any hot

surfaces.

Read the operating instructions for the fan before using.

5)

Plug fan into a properly grounded three prong receptacle.

Ground

Fan

Fan

Ground

Green

Neutral

Live

White

Fan

Switch

Manual/

Auto

Switch

Black

Black

High

(Black)

Low

(Red)

Black

Fan Thermodisc

(normally open)

120V AC

60 Hz

Blower/Fan Wiring Diagram

CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation.

WARNING: Electrical Grounding Instructions

This appliance is equipped with a three pronged
(grounding) plug for your protection against shock
hazard and should be plugged directly into a properly
grounded three-prong receptacle. Do not cut or remove
the grounding prong from this plug.

NOTE:

This appliance, when installed,

must be electrically grounded in accord-
ance with local codes or, in the absence
of local codes, with the National Electrical
Code, ANSI/NFPA 70, or the Canadian
Electrical code, CSA C22.1.

Automatic

To operate the fan automatically, push the bottom switch on the side of the fan housing to "AUTO" and the top switch to either "HIGH" or "LOW" for fan speed.

This will allow the fan to turn on as the stove has come up to operating temperature. It will also shut the fan system off after the fi re has gone out and the
unit cooled to below a useful heat output range.

Manual

To manually operate the fan system push the bottom switch to "MAN" and the top switch to either "HIGH" or "LOW". This will bypass the sensing device and
allow full control of the fan.

Switching from "AUTO" to "MAN" or "HIGH" to "LOW" may be done anytime.

FAN OPERATION

FAN WIRING

BLOWER/FAN INSTALLATION

Remove back panel

Install fan - under rear

heat shield

«
...
19
20
21
22
23
...
»

Содержание Alterra CS1200

































Отзывы:

Нет отзывов

Похожие инструкции для Alterra CS1200

Бренд: Panadero Страницы: 20

Бренд: HAAS + SOHN Страницы: 36

Бренд: Italiana Camini Страницы: 159

CLASSIC 400 Top Duo

Бренд: Harvia Страницы: 18

SCAN-LINE 805 AQUA

Бренд: Heta Страницы: 12

Бренд: Dovre Страницы: 48

Hamilton EL-BLT01

Бренд: e-Flame USA Страницы: 8

Бренд: Jydepejsen Страницы: 6

Бренд: Jydepejsen Страницы: 9

Бренд: Arada Страницы: 14

Бренд: Westfire Страницы: 3

Pelletto III 419.08

Бренд: Haas+Sohn Страницы: 15

Бренд: Cadel Страницы: 32

Бренд: Harman Stove Company Страницы: 32

Бренд: NESTOR MARTIN Страницы: 77

Ecofire Small 54

Бренд: Palazzetti Страницы: 8

Бренд: Palazzetti Страницы: 12

ECOFIRE BIANCA 12 PRO3

Бренд: Palazzetti Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды