Regency Fireplace Products E33-LP10 Скачать руководство пользователя страница 9

Страница: 9 / 32

E33-10 FPI Direct Vent Gas Insert

installation

MINIMUM FIREPLACE

OPENING (LOW PROFILE

FACEPLATE AND SPACER)

The minimum fireplace opening for the Regency gas

fireplace insert is shown in the following diagrams:

MINIMUM FIREPLACE

OPENING

The minimum fireplace opening for the Regency

gas fireplace insert when using the supplied spacer

is shown in the following diagrams:

18"

(457mm)

35-1/4" (895mm)

7-1/8”

(200mm)

Low profile

9-1/4"

(235mm)

25-1/2" (648mm)

18" (457mm)

GAS INSERT

AERATION SYSTEM

The air shutter can be adjusted by moving the

adjusting wire up or down. The wire is accessed

through the bottom louver opening. Open the air

shutter for a blue flame or close for a yellower

flame. The burner aeration is factory set but may

need adjusting due to either the local gas supply

or altitude.

Minimum Air Shutter Opening:

5/16"

Natural Gas

7/16"

Propane

CAUTION: Carbon will be produced if air

shutter is closed too much.

Note: Any damage due to carboning resulting

from improperly setting the aeration

controls is NOT covered under warranty.

Note: Aeration Adjustment should only be

performed by an authorized Regency

Installer at the time of installation.

Содержание E33-LP10

































Результаты поиска

Содержание E33-LP10

Отзывы:

Похожие инструкции для E33-LP10

Бренды по названию

Популярные бренды

Regency Fireplace Products E33-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание E33-LP10

Отзывы:

Похожие инструкции для E33-LP10

Бренды по названию

Популярные бренды