Regency Fireplace Products City ACB40ELP Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 87

background image

66

|

City Series ACB40E

installation

Propane/ULPG Conversion Instructions

920-217

03.12.20

1

CITY SERIES

CONVERSION FROM NG TO LP/ULPG

Using SIT 885 NOVA Gas Valve

Caution: The gas supply shall be shut off prior to disconnecting the
electrical power, before proceeding with the conversion.

Always let the appliance cool to room temperature before servicing.

1. Remove the outer panels and safety glass — see manual.

2. Remove inner ceramic glass — see manual.

3. Remove inner panels — see manual.

4. Remove all media installed on burner (glass, logs or stones, etc).

5. Disconnect the Cable coming from the Pressure Regulator Motor.

6. If unable to access this Cable - undo 2 screws securing the IFC Board

and slide out of unit to access cable.

WARNING

This conversion kit shall be installed by a qualified ser-
vice agency in accordance with the manufacturer’s in-
structions and all applicable codes and requirements
of the authority having jurisdiction. If these instructions
is not followed exactly, a fire, explosion or production
of carbon monoxide may result causing property dam-
age, personal injury or loss of life. The qualified service
agency is responsible for the proper installation of this
kit. The installation is not proper and complete until
the operation of the converted appliance is checked as
specified in the manufacturer’s instructions supplied
with the kit.

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION!

Cable from motor

Conversion Kit includes:

1

911-191

Stepper Motor LP for 885 SIT

1

904-947

Propane Orifice #53

1

910-037

Pilot Orifice #30

1

918-590

Decal - Conversion to LP

1

919-728

Orange "PROPANE" Label

1

905-039

ULPG Orifice #54

1

918-272

Conversion to ULPG decal

1

919-727

Red "UNIVERSAL LPG" Label

1

904-529

4mm Allen Key

1

920-217

Instruction Sheet

7. Remove and discard 2 Pressure regulator screws (A)using a (T20 or slot

screwdriver,) Pressure Regulator (B) and Spring and Diaphragm (C)
(see below).

8. Ensure the rubber gasket, which is prefitted as part of the Assembly,

is properly positioned. Install the new Pressure Regulator using the 2x
M4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event that
the screw threads are cross threaded or stripped, replace the valve as-
sembly.

Install the enclosed propane identification label to the valve body where it
can be easily seen.

Pressure
regulator

screws

9. Re-attach the Pressure Regulator wire (disconnected in Step 6), and re-

situate the IFC, secure the screws that fasten the IFC Mounting Brackets.

10. Remove pilot hood by lifting up and off.

«
...
64
65
66
67
68
...
»

Содержание City ACB40ELP
























































































Отзывы:

Нет отзывов

Похожие инструкции для City ACB40ELP

Бренд: T&C Страницы: 16

Бренд: Home Decorators Collection Страницы: 16

Бренд: St. Croix Страницы: 56

Бренд: Safavieh Furniture Страницы: 3

F-0710X1 series

Бренд: Hearth Products Страницы: 23

Бренд: Procom Страницы: 16

Бренд: Napoleon Страницы: 44

CITY LIGHTS Montcello

Бренд: Landmann Страницы: 2

Бренд: Teamson Home Страницы: 16

Бренд: Napoleon Страницы: 2

Бренд: Glow Fire Страницы: 241

Бренд: Amantii Страницы: 20

Бренд: Blue Rhino Страницы: 8

Бренд: Monessen Hearth Страницы: 1

Бренд: Blumfeldt Страницы: 124

Бренд: tropitone Страницы: 4

Бренд: JAYLINE Страницы: 11

Atraflam 16/9eme 600

Бренд: Atra Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды