Regency Fireplace Products Cascades I2500 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 40

background image

Regency I2500M

|

7

7

|

installation

View from Rear of Insert

INSTALLING YOUR
INSERT

Your insert is very heavy and will require two or
three people to move it into position. The insert
can be made a little lighter by removing the
cast iron door by opening it and lifting it off its
hinges. Be sure to protect your hearth extension
with a heavy blanket or carpet scrap during the
installation.

Convection Grills

The black convection grills are pre-installed on
this appliance.

If the optional nickel grills are being used, remove
the black grills and position the nickel grill on
the inside body face side and fasten using the
bolts, washers and nuts provided (2 per side)

Note: The grill has a front and rear, the holes

on the front side have rounded edges

and the rear holes have flat edges.

«
...
5
6
7
8
9
...
»

Содержание Cascades I2500









































Отзывы:

Нет отзывов

Похожие инструкции для Cascades I2500

Бренд: Magiglo Страницы: 48

Fireplace Surrounds None

Бренд: Dimplex Страницы: 2

Бренд: Travis Industries Страницы: 38

Бренд: Pacific energy Страницы: 24

Бренд: Napoleon Страницы: 4

Бренд: Monessen Hearth Страницы: 44

Бренд: Lennox Hearth Products Страницы: 30

Бренд: UltraGlow Страницы: 36

Бренд: HEAT GLO Страницы: 48

Бренд: Travis Industries Страницы: 3

Бренд: Lamborghini Caloreclima Страницы: 116

Бренд: Warmlite Страницы: 12

Бренд: Masport Страницы: 20

BALTIMORE MONACO NAPLES

Бренд: Masport Страницы: 44

Бренд: SJ COLLECTION Страницы: 22

Бренд: The Fireplace Страницы: 8

Бренд: Charnwood Страницы: 23

Бренд: Majestic fireplaces Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды