Regency Fireplace Products Bellavista B41XTE Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 84

background image

2

|

Regency Bellavista

®

B41XTE -11 Gas Fireplace

To the New Owner:

Congratulations!
You are the owner of a state-of-the-art Gas Fireplace by REGENCY

®

. The Bellavista™ B41XTE

has been designed to provide you with all  the warmth and charm of a wood fireplace at the flick
of a switch.  The Bellavista™ B41XTE has been approved by Warnock Hersey/Intertek for both
safety and efficiency.  As it also bears our own mark, it promises to provide you with economy,
comfort and security for many trouble free years to follow.  Please take a moment now to acquaint
yourself with these instructions and the many features of your Regency

®

Fireplace.

On Demand Pilot Light (seven day safety timer)

Important information if using the appliance in CPI (continuous pilot mode) only.
This appliance is a ProFlame 1 system fitted with the “On Demand” Pilot, a safety feature which will shut down the gas valve com-
pletely by extinguishing the pilot light in the event of a continuous full seven days of inactivity.
This only applies if the CPI (continuous pilot) switch is in the “on” position.
Each time the main burner shuts down, manually or through the call from the thermostat, the seven day timer starts again.
The seven day inactivity timer is controlled within the circuit board. Therefore, if in CPI mode and when the pilot light is extinguished
after seven straight days of inactivity, the IPI/CPI rocker switch will remain in the “on” position. Therefore, all that is required to relight
the pilot would be to press the on/off button on the remote control transmitter from “on” to “off” and back to “on”. Once the pilot has
re-established operation will resume as normal. There is no requirement to do anything with the IPI/CPI rocker switch.
If the unit never goes as long as seven full days without a call for heat, the pilot will remain lit until it is manually shut-off.
If the unit is being operated in IPI (intermittent pilot) mode, neither the above instructions nor the seven day timer will apply.
See the instructions in this manual and on the Lighting Instructions plate on the appliance to light or re-light the pilot.

«
1
2
3
4
...
»

Содержание Bellavista B41XTE





















































































Отзывы:

Нет отзывов

Похожие инструкции для Bellavista B41XTE

Бренд: Quadra-Fire Страницы: 28

Бренд: chazelles Страницы: 50

Бренд: GreatCo Страницы: 11

Бренд: Valcourt Страницы: 88

Бренд: Fire dept Страницы: 18

PONDEROSA LS-24P-1

Бренд: White Mountain Hearth Страницы: 12

Бренд: Napoleon Страницы: 56

Ecosmart Fire BK Series

Бренд: MAD Страницы: 14

Бренд: superior fires Страницы: 5

Бренд: EcoSmart Fire Страницы: 12

Бренд: Robinson Willey Страницы: 27

Бренд: Desa Страницы: 28

MILLIVOLT DVCD FP3-4 Series

Бренд: Empire Comfort Systems Страницы: 96

Бренд: Heatilator Страницы: 8

Бренд: Woodbridge Fireplace Inc Страницы: 20

STK-LIN60-B KIT

Бренд: IHP Страницы: 6

Бренд: IHP Страницы: 16

Бренд: Cosi Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды