background image

www.regency-fire.com

 

-  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other 

appliance. 

- WHAT TO DO IF YOU SMELL GAS
 • 

Do not try to light any appliance.

 

•  Do not touch any electrical switch: do not use any phone in your building.

 

  Leave the building immediately.

 

•  Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's  

instructions.

 

• If you cannot reach your gas supplier, call the fire department.   

 

• Installation and service must be performed by a qualified installer, service agency or 

       gas supplier.

     Warning
Fire or Explosion Hazard
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage. 

920-027j

    FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.  6988 Venture St., Delta, BC  Canada, V4G 1H4

06.18.21

Bellavista

®

 

B41XTE 

Gas Fireplace

Owners & 

Installation Manual

MODELS: B41XTE-NG11

                 B41XTE-LP11

Installer:  

Please complete the details on the back cover and leave this 
manual with the homeowner.

Homeowner

Please keep these instructions for future reference.

Certified to/Certifié pour:   CSA 2.17-2017
                                          ANSI Z21.88-2017
                                          CSA 2.33-2017

Tested by: 

French Manual: https://bit.ly/3tqzAtw

Manuel en français : https://bit.ly/3tqzAtw

Содержание Bellavista B41XTE





















































































Отзывы: