background image

Any revisions must first be approved by the product designer.   Version: 201808 

Revision By: JST 

 

 
 
 
 
 
 
 
 

 

11.

 

FASTENING GLASS

 

Secure the glass panels into the receiver 
channels by tightening hex key screws 
firmly with hex key supplied. DO NOT 
OVERTIGHTEN. 
 
 

 
 
 
 

12.

 

PROTECTION OF GLASS EDGE 

Apply 1mm plastic packer to the edge of 
glass with the masking tape as shown. 
Position one next to each hinge cut out. 

This will 
ensure 
correct 
door 
clearance 
and 
prevent 
glass 
damage.   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 

13.

 

CLEARANCE UNDER DOOR 

Place 6mm Spacers over the door infill 
before the installation of the glass door.  

 

14.

 

HINGE INSTALLATION 

Atlantis glass is now coated with 
CristalCote glass protection at the factory.  
This coating may cause the hinge to slip 
after installation.  Atlantis recommends 
cleaning around the hinge cut out prior to 
fitting hinges.  Clean both sides of the 
glass 15mm around the edge of the cut 
out with Fuelite (fuellite is available from 
petrol stations).  Alternatively, the area 
can be lightly sanded with 300grit 
sandpaper. 
 
 
 
 
 
 

ADJUSTABLE HINGES 

Atlantis showers are now supplied with 
adjustable hinges 

COVER PLATE REMOVAL 

Remove the cover 
plate by loosening the 
small grub screws on 
the edge of the hinge 
cover using a 1.5mm 
hex key.  Loosen the 
bolts with 4mm hex 
key.  Fit the hinges, 
the removable cover 
must be on the 
outside of the shower. 

Содержание Atlantis Glacier SFK-GL-HR
















Отзывы: