18
EN
RS 750-115 MA ● RS 1050-125 MA
ing power tools.
Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d)
Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e)
Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tool’s op-
eration. If damaged, have the power tool
repaired before use.
Many accidents are
caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g)
Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed.
Use of the power tool for op-
erations different from those intended could
result in a hazardous situation.
5) Service
a)
Have your power tool serviced by a
qualified repair person using only iden
-
tical replacement parts.
This will ensure
that the safety of the power tool is main-
tained.
Angle grinder safety
warnings
Safety Warnings Common for Grinding,
Sanding, Wire Brushing, Polishing or
Abrasive Cutting-Off Operations:
a)
This power tool is intended to func-
tion as a grinder, sander, wire brush,
polisher or cut-off tool. Read all safety
warnings, instructions, illustrations and
specifications provided with this power
tool.
Failure to follow all instructions listed
below may result in electric shock, fire and/
or serious injury.
c)
Do not use accessories which are
not specifically designed and recom
-
mended by the tool manufacturer.
Just
because the accessory can be attached to
your power tool, it does not assure safe op-
eration.
d)
The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool.
Accessories
running faster than their rated speed can
break and fly apart.
e)
The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
In-
correctly sized accessories cannot be ad-
equately guarded or controlled.
f)
The arbour size of wheels, flanges,
backing pads or any other accessory
must properly fit the spindle of the pow
-
er tool.
Accessories with arbour holes that
do not match the mounting hardware of the
power tool will run out of balance, vibrate
excessively and may cause loss of control.
g)
Do not use a damaged accessory. Be-
fore each use inspect the accessory
such as abrasive wheels for chips and
cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or
cracked wires. If power tool or acces-
sory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away
from the plane of the rotating accessory
and run the power tool at maximum no-
load speed for one minute.
Damaged ac-
cessories will normally break apart during
this test time.
h)
Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments.
The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of fil
-
trating particles generated by your opera-
tion. Prolonged exposure to high intensity
noise may cause hearing loss.
i)
Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protec-
tive equipment.
Fragments of workpiece
or of a broken accessory may fly away and
cause injury beyond immediate area of op-
eration.
j)
Hold the power tool by insulated grip-
ping surfaces only, when performing an
Содержание RS 1050-125 MA
Страница 90: ......
